3
1
●
In case of pet accidents on the connection area of the trays,
separate Upper and Lower Tray and clean the stain on the
surface and the connection areas thoroughly. Please be
careful not to drop the tray on a floor while cleaning.
●
Be careful of leakage of liquid/urine at the corners,
connections or/and rims.
3
2
①
Remove Short/Long Bolts (2) and Nuts (2). Please make sure to remove
correct bolts and nuts as shown on right figure.
②
Remove the Top Frame.
③
Remove the Wire Panel on the door side.
④
Attach Top Frame back to Front Panel B using Short/Long Bolts (2) and Nuts (2).
②
①
③
④
●
For Product Width of 35.4"
…
Use Short Bolts: left side (2 places) and right side (2 places)
●
For Product Width of 38 - 48"
…
Use Short Bolts: in the middle (2 places) and right side (2 places)
●
For Product Width of 50.6 - 60.6"
…
Use Short Bolts: right side (4 places)
(Product Width
38")
(Product Width
48")
(Product Width
50.6")
(Product Width
60.6")
Nut
Short Bolt
Long Bolt
Wire Panel
Front Panel B
Side Panel B
※
This image shows the Door Panel is
attached on left side of the crate.
Top Frame
※
Depending on the width of the crate, the position of Short Bolt varies.
When connecting Front Panel A to Front Panel B, if Front Panel B
overlaps and causes narrow entrance of the Front Panel A where
Door Panel will attach, remove the Wire Panel of Front Panel B by
following the steps below.
Front Panel A
Front Panel A
＋
Front Panel B
Front Panel A
Front Panel A
＋
Front Panel B
Front Panel A
Front Panel A
＋
Front Panel B
1-2. Determine the width of the crate
How to tighten Long / Short Bolts
Flat Washers
Short Bolt
Spring Washers
Attach Frames
Make sure to tighten the Nuts (16) on
Front/Back Panels.
※
Make sure to check that there are no loosened Nuts.
Position of Nuts (16)
Top Frame
Bottom Frame
Make sure to lap more than 2 rows of grooves
on Upper/Lower Tray as shown.
Attach Trays
The Floor Tray is designed to fit and expand with
Expandable Pet Crate.
Upper Tray
Lower Tray
Lap more than
two convex joints
Lap more than
two convex joints
Lap more than
two convex joints
Lower Tray is
marked "1"here.
Upper Tray is marked "2" here.
Firmly press the front-row convex joint of the
Upper Tray (See the arrows in the figure above)
until both Trays are fixed. (Only the front-row
convex has joint fixing grooves.)
Cautions!
Содержание 94920
