manualshive.com logo in svg

RHINO FN120, Руководство оператора

"RHINO FN120" - мощный инструмент для работы в саду и на приусадебном участке. Для полноценного использования необходимо ознакомиться с операторским руководством, которое можно бесплатно скачать на manualshive.com. Инструкция поможет вам эффективно использовать этот инструмент и получить от него максимальную отдачу.

Поделиться
Скачать
background image

SAFETY

FN180/FN120   07/12

Safety Section 1-14

© 2012 Alamo Group Inc.

SAFETY

HAZARDS WITH MAINTENANCE OF IMPLEMENT

AVOID SERIOUS INJURY OR DEATH FROM COMPONENT FAILURE BY KEEPING IMPLEMENT IN 
GOOD OPERATING CONDITION IN PERFORMING PROPER SERVICE, REPAIRS AND 
MAINTENANCE. 

BEFORE PERFORMING SERVICE, REPAIRS AND MAINTENANCE ON THE IMPLEMENT:
SECURE EQUIPMENT FOR SERVICE
BLOCK OUT POTENTIAL ENERGY HAZARDS; Rotating Parts, Raised Components, Hydraulic Pressure.

•

STOP ENGINE AND PTO

, engage parking brake, lower implement, allow all moving parts to stop and remove key before 

dismounting from tractor. 

•

PLACE

 implement on ground or securely block up raised equipment. Use large blocks on soft or wet soil.

•

SECURELY LATCH

 and 

LOCK

 raised implement wings

•

BLOCK UP IMPLEMENT TONGUE

 with large blocks and tongue jack. 

DO NOT

 crawl or work under implement supported only by 

tongue jack.

•

PUSH

 and 

PULL

 Remote Hydraulic Cylinder lever to relieve hydraulic pressure.

•

DISCONNECT IMPLEMENT

 Hydraulic 

HOSES

 from tractor

•

DISCONNECT IMPLEMENT

 driveline from tractor 

PTO SHAFT

.

WEAR SAFETY GLASSES, PROTECTIVE GLOVES 

and follow 

SAFETY PROCEDURES

 when performing service, repairs 

and maintenance on the implement:

•

Always 

WEAR

 protective 

GLOVES

 when handling blades, knives, cutting edges or worn component with sharp edges.

•

Always 

WEAR GLOVES

 and 

SAFETY GLASSES

 when servicing hot components

•

AVOID CONTACT

 with hot hydraulic oil tanks, pumps, motors, valves and hose connection surfaces.

•

SECURELY

 support or 

BLOCK UP

 raised implement, framework and lifted components before working underneath equipment.

•

STOP

 any implement movements and 

SHUT-OFF TRACTOR

 engine before doing any work procedures.

•

USE

 ladder or raised stands to reach high equipment areas inaccessible from ground.

•

ENSURE

 good footing by standing on solid flat surfaces when getting on implement to perform work.

•

FOLLOW

 manufacturer's instructions in handling oils, solvents, cleansers, and other chemical agents.

•

DO NOT

 change any factory-set hydraulic calibrations to avoid component or equipment failures.

•

DO NOT

 modify or alter implement, functions or components.

•

DO NOT WELD

 or repair rotating mower components. These may cause vibrations and component failures being thrown from 

mower. 

PERFORM SERVICE, REPAIRS, LUBRICATION AND MAINTENANCE OUTLINED IN IMPLEMENT MAINTENANCE 
SECTION:

•

INSPECT

 for loose fasteners, worn or broken parts, leaky or loose fittings, missing or broken cotter keys and washers on pins, and 

all moving parts for wear.

•

REPLACE

 any worn or broken parts with authorized service parts.

•

LUBRICATE

 unit as specified by lubrication schedule

•

NEVER

 lubricate, adjust or remove material while it is running or in motion.

•

TORQUE

 all bolts and nuts as specified.

BLADE INSPECTION:

•

REPLACE

 bent, damage, cracked or broken blades immediately with new blades.

•

AVOID

 blade failures and thrown broken blades. 

DO NOT

 straighten, weld, or weld hard-facing blades.

SAFETY SHIELDS, GUARDS AND SAFETY DEVICES INSPECTION:

•

KEEP

 all Deflectors, Chain Guards, Steel Guards, Gearbox Shields, and PTO integral shields, Bands, Side Skirts and Skid Shoes 

in place and in good condition.

•

REPLACE

 any missing, broken or worn safety shields, guards and safety devices.

•

Engine Exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the state of California 
to cause cancer, birth defects or other reproductive harm.

•

Battery posts, terminals and related accessories contain lead and lead compounds, chemicals known to the state of California to 
cause cancer, birth defects or other reproductive harm.   

PN HM01

Содержание FN120

































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FN120

Yard force MB 800 Safety Instruction preview
MB 800
Бренд: Yard force Страницы: 45
Snapper 85673 Parts Manual preview
85673
Бренд: Snapper Страницы: 84
McCulloch 532 42 27-27 Rev. 2 Operator'S Manual preview
532 42 27-27 Rev. 2
Бренд: McCulloch Страницы: 28
EarthWise 1819-18EW Owner'S Manual preview
1819-18EW
Бренд: EarthWise Страницы: 9
COMPANION COMPANION 27826 Instruction Manual preview
COMPANION 27826
Бренд: COMPANION Страницы: 84
Villager FALCON 6111H Operator'S Manual preview
FALCON 6111H
Бренд: Villager Страницы: 128
Urrea TGZ950 User Manual And Warranty preview
TGZ950
Бренд: Urrea Страницы: 40
Cub Cadet 23HP Z-Force 60 Operator'S And Service Manual preview
23HP Z-Force 60
Бренд: Cub Cadet Страницы: 32
Spear & Jackson SPJPM40B Operating Instructions Manual preview
SPJPM40B
Бренд: Spear & Jackson Страницы: 24
McCulloch M195-42T Operator'S Manual preview
M195-42T
Бренд: McCulloch Страницы: 60
Poulan Pro 960 41 01-39 Illustrated Parts List preview
960 41 01-39
Бренд: Poulan Pro Страницы: 17
Bushranger 46TBU6 Owner'S Manual preview
46TBU6
Бренд: Bushranger Страницы: 20
Generac Power Systems PRO AT45026GENG Owner'S Manual preview
PRO AT45026GENG
Бренд: Generac Power Systems Страницы: 28
Brave BRPRC108HEB Owner'S Manual preview
BRPRC108HEB
Бренд: Brave Страницы: 24
Jonsered JNA19H48B Owner'S Manual preview
JNA19H48B
Бренд: Jonsered Страницы: 48
Jonsered J160FH22 Operator'S Manual preview
J160FH22
Бренд: Jonsered Страницы: 40
Simplicity ZERO TURN TP 400-2169-01-ZT-SMA Parts Manual preview
ZERO TURN TP 400-2169-01-ZT-SMA
Бренд: Simplicity Страницы: 46
EINHELL 34.132.76 Original Operating Instructions preview
34.132.76
Бренд: EINHELL Страницы: 128

Бренды по названию

Популярные бренды

Загрузить еще бренды