RHINO FN120 Скачать руководство пользователя страница 150 | Manualshive

Страница: 150 / 224

background image

OPERATION

FN180/FN120 07/12

Operation Section 4-44

© 2012 Alamo Group Inc.

OPERA

T

ION

Tire Size and Matching requirements - Center Axle

Tire assemblies when mounted on center axle duals should always be within limits listed.

Laminated Tires - Maximum difference between tire diameters on a center axle should be 1/2 inch or less.

Foam Filled Airplane Tires - Maximum difference between tire diameters on a center axle should be 1 inch or
less.

When replacing a tire assembly on center axle always check diameters to make sure tires fall within allowed
range for maximum tire and wheel life. It may be necessary to move one or more tires from wing axles to
remain within size limit.

13.1 Tire and Wheels

Laminated Sectional Tires

are designed for conditions where puncture proof performance is required and

the mower will not be transported for long distances on roadways. Transport speed for laminated tires should
not exceed 15 MPH. Excessive speed can cause damage to the machine and tire sections. Laminated tires
must be installed such that the rubber segments lay with the ground.

Foam Filled used Airplane Tires

are ideal for conditions where a puncture proof tire is needed and the

mower is frequently transported between locations.

Pneumatic Tires

Implement tires are ideal for frequent long distance towing, however, they are not puncture

proof and are not recommended for mowing brushy areas or other conditions that could damage the tires.
Check side wall of tire for proper inflation pressure. DO NOT over-inflate.

OPS-R-0035

«
...
148
149
150
151
152
...
»

Содержание FN120

































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FN120

Бренд: MTD Страницы: 6

Бренд: Qualcast Страницы: 24

Бренд: Poulan Pro Страницы: 52

Бренд: Supaswift Страницы: 12

Бренд: Simplicity Страницы: 54

54-pro k vario plus

Бренд: Sabo Страницы: 92

Бренд: Yard-Man Страницы: 16

Бренд: Snapper Страницы: 32

Бренд: DR Страницы: 44

Бренд: Toro Страницы: 28

Бренд: VonHaus Страницы: 12

135 B TITAN DOD

Бренд: Stiga Страницы: 100

Бренд: Spear & Jackson Страницы: 2

Бренд: Grizzly Страницы: 96

Бренд: VITO GARDEN Страницы: 20

Бренд: Craftsman Страницы: 16

Бренд: Craftsman Страницы: 20

Бренд: Craftsman Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды