RHINO FN120 Скачать руководство пользователя страница 188

Страница: 188 / 224

MAINTENANCE

FN180/FN120 07/12

Maintenance Section 5-32

MAINTENANCE

RIGHT ANGLE GEARBOX (OUTBOARD) ASSEMBLY & DISASSEMBLY
PROCEDURES

INPUT SHAFT REMOVAL

Step I.

Place Gearbox on appropriate work surface.

Step II.

Remove Vent Plug (30) or Complete Top Cover (26).

Step III.

Turn Gearbox upside down allowing Oil to drain from gearbox into catch pan for proper disposal.

Step IV.

Turn Gearbox right side up and drop bottom into a hole for support or lay it on its side laying flat.

Step V.

Remove Bolts (3) from rear Bearing Cap (21), this will allow front cover to be removed. Tap on end of input

shaft to remove cap. Repeat procedure for front cap (4).

Step VI.

Remove Input shaft (5) by tapping on drive spline end. Shaft will come through rear cap opening leaving gear

(32) & Bearing (20) in main housing.

Step VII.

Remove rear Bearing (20), bearing Spacer (24), and short spacer (29).

Step VIII

Remove Input Seal (6), from cap (4). Remove bearing cap (30) from input cap bore.

Output Shaft Removal

Step I.

Remove Cotter Pin (19) from Nut (18).

Step II.

Slide Output (Pinion) Gear (17) up off of Output Shaft and out of Main Housing. Note quantity of shims under

gear.

Step lll.

Output Shaft will come out of Main Housing through the bottom.

Step lV.

Reach in from front or top of Main Housing and remove upper Output Shaft Cone Bearing (20).

Содержание FN120

































































































































































































































Результаты поиска

Содержание FN120

Отзывы:

Похожие инструкции для FN120

Бренды по названию

Популярные бренды

RHINO FN120, Руководство оператора

Результаты поиска

Содержание FN120

Отзывы:

Похожие инструкции для FN120

Бренды по названию

Популярные бренды