RHINO FN120 Скачать руководство пользователя страница 173 | Manualshive

Страница: 173 / 224

background image

MAINTENANCE

FN180/FN120 07/12

Maintenance Section 5-17

© 2012 Alamo Group Inc.

MAINTENANCE

Assembly (Cont’d)

9. Using the large driver used in disassembly, drive

one of the bearing cups into the yoke until the
groove for the snap ring can be seen. Make sure
the ear of the yoke is flat against the bench. If
the grease fitting in the yoke is down, support
the yoke on a block to prevent damage to the
grease fitting.

10.Make sure the groove for the snap ring is clean.

Install the snap ring. Use a screwdriver to push
the snap ring into the groove all the way around.

11. Set the shaft yoke on the vise so the shoulders

of the cross are supported by the jaws of the
vise.

DO NOT

allow the machined surfaces to

contact the vise. Hit the yoke with the hammer to
seat the bearing cup against the snap ring.

DO

NOT

hit the yoke near the opening for the

bearing cup. (MntP-R-0171)

12.Repeat Steps 9-11 for the other snap ring.

13.Repeat steps 1-12 for the end yoke.

14.Wrap a shop cloth around the shaft to protect

the splines. Clamp the shaft in the vise so that
shaft yoke is up. The ball in the shaft yoke has a
flat area around each end of the hole. The flat
area is wider on one side of the ball.(MnR-0454)

15.Rotate the center housing so the grease fitting is

away from the shaft yoke. This will align the
grease fitting in the center housing with the hole
in the guards. The grease fittings in the center
housing and the cross must be toward the same
side of the assembly. Make sure the pin of the
center plate in the center housing is clean. Install
the pin in the ball and cross in the ears of the
center housing. (MntP-R-0172)

16.Make sure there is grease in the holes for the

bearing cups in the center housing. Push the
cross to one side of the yoke.

17.Use the cross trunnion as a pilot. Start the new

bearing cup on the cross and into the opening in
the center housing. Push the cross into the
bearing cup while driving the trunnions of the
cross parallel with the openings for the bearing
cups. Hit the bearing cup lightly with a hammer.
Using the vise, drive the bearing cup in to the
yoke until the bearing cup is flush with the yoke
ear. (MntP-R-0173)

«
...
171
172
173
174
175
...
»

Содержание FN120

































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FN120

Бренд: Parkside Страницы: 60

Бренд: Snapper Страницы: 44

Бренд: Jacobsen Страницы: 98

Pro 12 DFS 37621231

Бренд: Peco Страницы: 32

Бренд: Toro Страницы: 28

Бренд: Scag Power Equipment Страницы: 41

Бренд: VITO GARDEN Страницы: 20

Бренд: Craftsman Страницы: 26

Бренд: Craftsman Страницы: 26

Бренд: Craftsman Страницы: 12

Бренд: Craftsman Страницы: 30

Бренд: Craftsman Страницы: 36

Бренд: Craftsman Страницы: 28

Бренд: Craftsman Страницы: 40

Бренд: Craftsman Страницы: 40

Бренд: Craftsman Страницы: 22

Бренд: Craftsman Страницы: 52

Бренд: Craftsman Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды