RHINO FN120 Скачать руководство пользователя страница 21

Страница: 21 / 224

SAFETY

FN180/FN120 07/12

Safety Section 1-11

SAFETY

HIGH PRESSURE OIL LEAK HAZARD

TO AVOID SERIOUS INJURY OR DEATH FROM HIGH PRESSURE HYDRAULIC OIL LEAKS
PENERATING SKIN:

•

DO NOT OPERATE

equipment with oil or fuel leaks.

•

KEEP

all hydraulic hoses, lines and connections in

GOOD CONDITION

and

TIGHT

before applying system

pressure.

•

RELIEVE HYDRAULIC PRESSURE

before disconnecting lines or working on the system.

•

REMOVE

and replace hose if you suspect it leaks. Have dealer test it for leaks.

HIGH PRESSURE FLUID LEAKS CAN BE INVISIBLE.
WHEN CHECKING FOR HYDRAULIC LEAKS AND WORKING AROUND HYDRAULIC SYSTEMS:

•

ALWAYS WEAR

safety glasses and impenetrable gloves.

•

USE

paper or cardboard to search for leaks.

•

DO NOT USE

hands or body parts to search for leak.

•

KEEP

hands and body

AWAY

from pin holes and nozzles ejecting hydraulic fluid.

•

Hydraulic fluid may cause gangrene if not surgically removed immediately by a doctor familiar with this form of injury.

PN HP01

Содержание FN120

































































































































































































































Результаты поиска

Содержание FN120

Отзывы:

Похожие инструкции для FN120

Бренды по названию

Популярные бренды

RHINO FN120, Руководство оператора

Результаты поиска

Содержание FN120

Отзывы:

Похожие инструкции для FN120

Бренды по названию

Популярные бренды