RHINO FN120 Скачать руководство пользователя страница 130

Страница: 130 / 224

OPERATION

FN180/FN120 07/12

Operation Section 4-24

OPERA

ION

8.4 Blade Bolt Inspection

Inspect Blade Bolt Head daily for wear as followed:

Inspect the Blade Bolt Heads daily for abnormal wear. REPLACE BOTH BLADE BOLTS on
the Blades IMMEDIATELY if either blade bolts has:

•

Visible cracks or

•

If the recessed area on blade bolt is worn off or

•

If Blade Bolt has gouges or chipped areas.

Failure to replace abnormally worn blade bolts may lead to catastrophic failure of the blades and ejection of
the broken part which may cause serious bodily injury or death.

Always replace Blade Bolts with new bolts whenever replacing the Blades.

OPS-U-0037

Содержание FN120

































































































































































































































Результаты поиска

Содержание FN120

Отзывы:

Похожие инструкции для FN120

Бренды по названию

Популярные бренды

RHINO FN120, Руководство оператора

Результаты поиска

Содержание FN120

Отзывы:

Похожие инструкции для FN120

Бренды по названию

Популярные бренды