Rhin-O-Tuff APES-14 HD-6500 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 21

background image

¾

Place the APES-14 Ejector Base Plate Assembly on top of the HD punch. Avoid

colliding the APES-14 Front Paper Guides and the Drive Motor Assembly with
the HD punch while setting it down. Keep control cable clear. See Figure E.

Fig. E-2

Ejector Top Plate Assembly on an HD punch

¾

Push and maintain the APES-14 Ejector Base Plate Assembly lightly back

against the front of the HD punch and install and tighten the two 3-winged
mounting knobs provided. See Figure E-2.

¾

Move the APES-14 Reception Assembly next to the HD punch. See Figure F.

Note that the Reception Pivot Block will align centered about the Ejector Base
Plate Reception Mounting Bar as shown. See Figure G.

Fig. F Fig. G

Move the APES-14 Reception next to the HD punch

Page 6

Issue “A1” 09/03 PDI Part # 900600 www.RHIN-O-TUFF.com

«
...
6
7
8
9
10
...
»

Содержание APES-14 HD-6500






















Отзывы:

Нет отзывов

Похожие инструкции для APES-14 HD-6500

Бренд: Jack Страницы: 74

Бренд: Antari Страницы: 12

3001 Silent Drive

Бренд: ProForm Страницы: 16

Бренд: Necci Страницы: 39

Бренд: Kärcher Страницы: 22

Бренд: Singer Страницы: 109

Бренд: BoomToneDJ Страницы: 14

Бренд: Blaupunkt Страницы: 68

Бренд: JUKI Страницы: 20

Бренд: JUKI Страницы: 28

Бренд: JUKI Страницы: 52

Бренд: JUKI Страницы: 164

Бренд: JUKI Страницы: 62

Бренд: Stern Pinball Страницы: 52

Бренд: Singer Страницы: 38

Бренд: Kettler Страницы: 12

Folder Express 3001

Бренд: Canon Страницы: 5

Бренд: Janome Страницы: 182

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды