REWIRE SECURITY DB3 Скачать руководство пользователя страница 95

Страница: 95 / 122

9.5.5.2 Min Saved Records (ID=1583)

This parameter defines the minimum number of records in one data packet
that can be sent to the server. It has higher priority than Data Send Period
(ID=1584).

Minimum
value

Maximum
value

Recommended

value

Goes with (depends on)
parameters

Value
type

255

GPRS Week Time
(ID=1585)

9.5.5.3 Send Period (ID=1584)

This parameter indicates frequency (time interval in seconds) of sending data
to the server.

Minimum
value

Maximum
value

Recommended

value

Goes with (depends on)
parameters

Value
type

2592000

Min Saved Records
(ID=1583) GPRS Week
Time (ID=1585)

U32

9.5.5.4 GPRS Week Time (ID=1585)

Read

GPRS Week Time (ID=1545)

9.5.6 Unknown Network GSM

Operator Code “

Vehicle MOVING

”

Parameters

9.5.6.1 Min Period (ID=1590)

This parameter indicates time interval in seconds in order to acquire new
record. If the value is 0 it means no records by min period will be saved.

Содержание DB3



























































































































Результаты поиска

Содержание DB3

Отзывы:

REWIRE SECURITY DB3, Руководство пользователя, Страница: 95 / 122

Результаты поиска

Содержание DB3

Отзывы: