manualshive.com logo in svg

REWIRE SECURITY DB3, Руководство пользователя, Страница: 33 / 122

Поделиться
Скачать
REWIRE SECURITY DB3 Скачать руководство пользователя страница 33

ATTENTION! If you have entered a keyword, disconnected from 
the configurator and then later connected again, you will need 
to enter the keyword that you have entered previously. If you 
have forgotten it, please contact your local sales manager.  

 

5.7

  

Record Storage  

 

DB3 Plug&Play can store up to 8000 data records if GSM or GPRS is not 
available at the moment. It will send data later when GPRS is available again. 
Note that DB3 Plug&Play can have a memory full of records. In such case, it will 
start deleting oldest records in order to save new ones. Sending all the data 
records to the server may take some time. Sending 8000 records for DB3 
Plug&Play may take for about 2 hours (exact time may differ depending on 
GPRS/server load).   

You can access all uploaded data from the TAVL4 application.  

More details on how to use TAVL application please refer to “TAVL4 application 
user manual” documentation. 

 

5.8   System Settings  

 

System settings have 6 configurable parameters

:  

Sleep settings

, where the user can turn sleep/deep sleep on or off;  

Mode Switch Settings

, where the user can configure 3 ways how DB3 

Plug&Play will change its working mode;  

Ignition Settings

, where the user can configure ignition detection source (for 

ignition source). Ignition Source can be selected as Power Voltage, Digital Input 
1 or Movement. This parameter has an influence on all DB3 Plug&Play 
application. If an ignition source is set to Power Voltage ranges for ignition 
detection must be configured. Ignition is set to 1 when Power Voltage is in the 
range between Low & High Power Voltage Levels.  

Static Navigation – when this parameter is enabled, DB3 Plug&Play filters out 
GPS jumps when the vehicle is not moving. When it is disabled, it does not 
make any changes to collected GPS data.   

Содержание DB3



























































































































Отзывы:

Нет отзывов