REWIRE SECURITY DB3 Скачать руководство пользователя страница 77

Страница: 77 / 122

Minimum
value

Maximum
value

Recommended

value

Goes with (depends on)
parameters

Value
type

Power Voltage Low Level

(ID=1006)

Power Voltage Level High
Level (1007)

9.2.5 Static navigation settings (ID=1004)

When static navigation is enabled, DB3 Plug&Play filters out GPS jumps, when
it is not moving. When it is disabled, it does not make any changes to collected
GPS data. 0 - disabled (default); 1 - enabled.

Minimum
value

Maximum
value

Recommended

value

Goes with (depends on)
parameters

Value
type

9.2.6 Saving/Sending without time synchronization (ID=1005)

When this feature is enabled (value = 1), then records can be saved and sent to
the server without time synchronization.

Minimum
value

Maximum
value

Recommended

value

Goes with (depends on)
parameters

Value
type

9.2.7 Power Voltage Low Level (ID=1006)

When ignition source is selected as Power Voltage Low level for ignition
detection must be set.

Minimum
value

Maximum
value

Recommended

value

Goes with (depends on)
parameters

Value
type

Содержание DB3



























































































































Результаты поиска

Содержание DB3

Отзывы:

REWIRE SECURITY DB3, Руководство пользователя, Страница: 77 / 122

Результаты поиска

Содержание DB3

Отзывы: