REWIRE SECURITY DB3 Скачать руководство пользователя страница 69

Страница: 69 / 122

6.1.16 Crashlog

Gives the last information before the device has crashed for unexpected
reasons. It is useful when the device acts unexpectedly or restarts for
unexplained reasons.

Example if no unexpected reset

: “Crash: “

Example if unexpected reset was detected

: “Crash: 3051,3052,3053”.

6.1.17 Defevt

This SMS command resets SMS Events configuration to default.

Example

: SMS Event default parameters loaded.

6.1.18 Battery

Returns DB3 Plug&Play battery information.

Example

: BatState: 1 FSMState: ACTIVE ChargerIC: CHARGING ExtV:

14020 BatV: 3800 BatI: 50 PCBTemp: 35.2.

6.1.19 Cleardtc

Clears all vehicle stored trouble codes and turns the MIL off.

Example

: DTC cleared: OK; or: DTC cleared: ERROR.

6.1.20 Obdinfo

Response details

Description

LIST of OBD info Protocol, VIN, AdaptiveTiming value, requested PID

counter, OBD application state, available vehicle PIDs,
fuel calc method, mil status, number of DTCs

Example

:Protocol:5,VIN:N/A,TM:5,CNT:5,ST:OBDDATA

REQUESTING,P1:0x0,P2:0x0,P3:0x0,P4:0x0,Fuel: ELOAD,MIL:0,DTC:0,ID0

Содержание DB3



























































































































Результаты поиска

Содержание DB3

Отзывы:

REWIRE SECURITY DB3, Руководство пользователя, Страница: 69 / 122

Результаты поиска

Содержание DB3

Отзывы: