REV FIRST Global Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 56

background image

FIRST Global Building Guide Created by REV Robotics 2019, Licensed Under CC BY-SA

27

3.9

ADAPTERS

3.9.1

Hex Hub Adapter

The aluminum hex hub adapter should be added in any high torque application. The Hex hub adapter has mounting 4
mounting holes and are compatible with any of the REV robotics hex driven motion products.

Hex Hub Adaptor

REV-41-1146

When the hex hub adaptor is used with another motion component, such as the 60 tooth gear in Figure 46, the raised part
of the hub should face away from the gear. There will be a small gap between the back of the hub and the body of the
gear because of the built-in spacer on the gear. Insert a shaft into both parts and then using M3x20mm and nylocs, evenly
tighten the hub against the gear to ensure good alignment.

Figure 46: Hex Hub Adapter Mounted on a REV Gear for Added Strength

3.9.2

Servo Adapters

Servo Adapters fit 25T spline servos like the REV Robotics Smart Robot Servo (REV-41-1097). In addition to the variety
pack of generic servo horns which come with the Smart Robot Servo, there are three other custom servo adapters which
make using servos with the REV Robotics building system very easy (Table 6).

Table 6: Servo Adapters

Servo Gear Adaptor

REV-41-1364

Servo Shaft Adaptor

REV-41-1328

Aluminum Servo Horn

REV-41-1363

Servo Gear Adaptors

convert a 25T servo into 15 tooth Delrin gear which is compatible with the other REV

Robotics Gears.

Servo Shaft Adaptors

convert a 25T spline servo output shaft into a female 5mm hex socket. This adapter can be

used to use a servo to drive a 5mm hex shaft directly.

Aluminum Servo Horns

have a tapped hole pattern that can be directly mounted to any of the REV Robotics gears,

wheels, or sprockets with a 6-hole pattern.

«
...
27
28
29
30
31
...
»

Содержание FIRST Global

























































Отзывы:

Нет отзывов

Похожие инструкции для FIRST Global

Бренд: IEI Technology Страницы: 6

Бренд: KBS Страницы: 268

Бренд: Kuka Страницы: 109

ST5-1300-2000DT-S

Бренд: Shini Страницы: 176

Бренд: Nachi Страницы: 190

Бренд: SeaBotix Страницы: 101

Dobot Vision Kit

Бренд: ShenZhen Yuejiang Technology Страницы: 19

Бренд: Thames & Kosmos Страницы: 68

Бренд: AATA INTERNATIONAL Страницы: 25

Robo 2.0 Canoe Trip

Бренд: Artec Страницы: 10

Бренд: Meccano Страницы: 18

Бренд: IBM Страницы: 98

Бренд: SoftBank Страницы: 4

Бренд: Steren Страницы: 62

Бренд: Mecademic Страницы: 110

Бренд: Plum Geek Robotics Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды