REV FIRST Global Скачать руководство пользователя страница 22

Страница: 22 / 56

FIRST Global Building Guide Created by REV Robotics 2019, Licensed Under CC BY-SA

3.6.2

Assembly Instructions

These instructions explain how to build one half of a single stage lift. Each REV Robotics 15mm Linear Motion Kit
contains enough hardware to create a 2-stage lift.

Step 1

Required Components:

Slider Plate

–

M3 x 8mm Hex Cap Bolts

–

M3 Nylon Locknuts

–

Make sure the bolts are not fully tightened down so that

the whole assembly can be slid onto a piece of extrusion

later.

Step 2

Required Components:

Double Sided Slider

–

M3 x 8mm Low Profile Socket Cap Bolts

–

M3 Nut

–

Be sure that you insert the bolt from the correct side

because the double-side slider is not completely

symmetric. The bolt head should be on the side with the

round cutout.

Step 3

When assembling the double-sided slider, only tighten the

nut so that it is flush with the bottom of the slider when

the bolt head is all the way down. There should be

clearance between the top of the nut and the slider as

shown.

Step 4

Insert the double-sided slider into the extrusion channel.

You may have to slightly loosen or tighten the nut so that

it will align with the channel.

Once the slider is fully inserted into the channel, tighten

the bolts just until snug,

OVERTIGHTENING MAY CAUSE

SLIDER DEFORMATION AND BINDING.

Содержание FIRST Global

























































Результаты поиска

Содержание FIRST Global

Отзывы:

Похожие инструкции для FIRST Global

Бренды по названию

Популярные бренды

REV FIRST Global, Руководство по эксплуатации

Результаты поиска

Содержание FIRST Global

Отзывы:

Похожие инструкции для FIRST Global

Бренды по названию

Популярные бренды