REV FIRST Global Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 56

background image

FIRST Global Building Guide Created by REV Robotics 2019, Licensed Under CC BY-SA

8

relative encoder does not know what position it is in when it is turned on, but it is possible to create a calibration program
that can be run at every start-up to obtain a reference point from which to calculate an angle.

The encoder uses four wires, 3.3V Power, Ground, Channel A and Channel B to communicate data back to the Hub (Figure
11). When the motor is rotating, the Hub can calculate the direction and speed of the motor.

Figure 11: Encoder Connector Pinout

2.6

BATTERY

The Slim Robot Battery for FIRST Global is a 12V 3000mAh NimH battery with inline 20A mini ATX fuse for protection
(Figure 12). The battery has a female XT30 Connector. This connector is polarized so that the battery cannot be plugged
in incorrectly.

Figure 12: Slim Robot Battery

2.6.1

Battery Safety

Batteries store tremendous energy in a small size and it is important to take care of your batteries to keep them in good
working order and to prevent dangerous conditions.

-

Batteries should only be charged with approved chargers

-

Never leave a charging battery unattended

-

Do not leave a battery plugged into a robot when it is not in use and avoid other cases where a battery will be
accidentally over discharged

-

Batteries should be fully charged before they are put in storage for extended periods

-

Properly dispose of any battery which has been damaged or which shows any signs of excessive heat or melting

«
...
8
9
10
11
12
...
»

Содержание FIRST Global

























































Отзывы:

Нет отзывов

Похожие инструкции для FIRST Global

Бренд: ABB Страницы: 510

Бренд: Motoman Страницы: 25

Бренд: Makeblock Страницы: 9

Бренд: SeaBotix Страницы: 101

Бренд: neobotix Страницы: 45

Бренд: UBTECH Страницы: 26

Бренд: Velleman Страницы: 14

Бренд: YFRobot Страницы: 8

Бренд: Learning Resources Страницы: 16

Бренд: Kitronik Страницы: 4

MOVE Motor Klaw

Бренд: Kitronik Страницы: 3

LINE FOLLOWING BUGGY V3

Бренд: Kitronik Страницы: 12

Бренд: Blue point Страницы: 42

Бренд: Kondo Страницы: 58

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды