Renishaw UCC2 Скачать руководство пользователя страница 49

Страница: 49 / 60

Troubleshooting

To aid troubleshooting of the UCC2 system, five status LEDs are visible through the front panel of the UCC2.

LED

System status

Refer to section

Power on

System ready

Servo active

Probe seated

Error

off

Power off

UCC2 power not

switched ON

off

Default start up

condition

UCC2 power

switched ON

UCC2 power not switched ON

All LEDs OFF.

UCC2 power switched ON

Power on LED is lit.

If switch-on is successful the UCC2 proceeds to the initialisation/test sequence.

Initialisation / test

If the initialisation tests fail, then after about 15 seconds three LED configurations are possible, each indicating a different form of failure:

Power on

System ready

Servo active

Probe seated

Error

Off

Flashing slowly

Flashing fast

Off

NOTE:

These failures are not fixable at the customer's site - if any of these forms of failure are indicated the unit must be returned

to your local Renishaw office.

NOTE:

The state of all LEDs being off except ‘power on' is the normal switch‐on state ﴾as per "UCC2 power switched ON"﴿; it only

indicates failure if it remains like this beyond about 15 seconds.

Try switching the controller off, waiting about 10 seconds, then turning it on again. If the problem persists, the unit needs attention.

If initialisation tests are successful, the power on LED will remain lit and the error LED will start flashing. A slow flash (approximately 0.5

second period) indicates the system is ready for a download. A fast flash (approximately 0.2 second period) indicates the UCC2 is in its IP

configured state (see

"Configuration of IP addresses"

UCC2 and UCC2-2 installation guide

www.renishaw.com

Issued 07 2021

Содержание UCC2





























































Результаты поиска

Содержание UCC2

Отзывы:

Похожие инструкции для UCC2

Бренды по названию

Популярные бренды

Renishaw UCC2, Руководство по установке

Результаты поиска

Содержание UCC2

Отзывы:

Похожие инструкции для UCC2

Бренды по названию

Популярные бренды