REMA TLM77 RMH/100 Скачать руководство пользователя страница 8

 

 

 

5.2  

Method of operating 

5.2.1   Lifting 

Put a weight on the tooth plate of jack stable. 
Attention: Can not use the front end of tooth plate to lift the weight. 
Important point: When lifting the weight by the tooth plate, the weight should be close 
to the head of jack to avoid the pillar (47) of jack being bent. 
Please screw in the unloaded handle (16) tightly in clockwise direction before lifting. 
Then press and lift the operating handle up and down repeatedly to pump the 
pressure to lift the weight. The lifting movement can be stopped immediately by 
stopping the lifting operation. 

5.2.2   Reducing 

Please screw out the unload handle slowly in anti-clockwise direction to reduce the 
weight step by step. But when screw up the round unload handle again, the reducing 
movement can be stopped instantly. 
Note: When the jack is in unloaded condition, the head of it should be pressed to 
reduce its height. 
Attention:  If  the  jack  is  not  in  the  state  of  maintaining,  each  part  of  it  can  not  be 
dismantled except the operating handle. 

5.3  

Safety standard 

5.3.1   The  lifting  of  weight  is  dangerous  operation,  the  appointed  operators  should  be 

professional, be trained and be experienced. 

5.3.2   Those  extra  weights  can  not  be  added  on  the  lifted  weight  to  avoid  dropping 

accident happening. 

5.3.3   Never exceed the recommended maximum limitation of lifting weight. 
5.3.4   Please keep a safety distance with the lifted weight. 
5.3.5   Never use the jack, or being changed or spoilt, or in bad condition itself. 
5.3.6   When lifting the weight by tooth plate, please keep the weight close to the head of 

jack to avoid the pillar of jack being bent. Please check the drawing again. 

5.3.7   Please confirm that each support point of ground should be solid and stable including 

floor  area  and  loading  etc,  then  any  type  of  operating  should  be  handled  on  the 
plane surface only. 

5.3.8   Please  guarantee  the  lifted  weight  stable  during  the  whole  lifting  period  to  avoid  it 

being turn over or being slipped. Each device shall be fixed before lifting. 

5.3.9   Never operating the jack when people standing on the lifting weight. 
5.3.10  Never use the front end of the tooth plate to lift weight. The tooth plate should be 

located in its base totally, the pushing point to the weight should close to the back 
end of tooth plate as far as possible. 

5.3.11  Never screw the adjustable screw  (18),  under any circumstance,  otherwise a typical 

accident of jack dropping might be happened. These parts (10,11,18,19,20,21) are the 
device of overloading protection. 

5.3.12  Never use the side of jack's head to lift weight. The weight should be contacted with 

the black shadow surface of the following pictures. 

Содержание TLM77 RMH/100
































Отзывы: