Regulus SRS6 Скачать руководство пользователя страница 46

 

46

REGULUS SRS6 EP Controller - www.regulus.eu

Special functions 

menu 6

6.5.2. – VFS (X)   

 

 

 

 

menu 6.5.2

6.5.2.1 – VFS Type   

 

 

 

menu 6.5.2.1

The VFS type is set here

Settings range: Off; 1-12; 1-20; 2-40; 5-100; 10-200; 20-400 / Default setting: Off

6.5.2.2. - VFS - Position 

 

 

 

menu 6.5.2.2

This setting determines the position of the VFS 

fl

owmeter with temperature sensor.

Settings range: 

fl

ow, return / Default setting: return

Warning:

To prevent damage to the Vortex Flow Sensor it is strongly recommended to install it into the return 

fl

ow. If it is necessary to install in the 

fl

ow, it is imperative not to exceed the maximum temperatures 

of the sensor! (0° C to 100 °C and -25 °C to 120 °C short term.)

6.5.2.3. – Reference sensor 

 

 

menu 6.5.2.3

 

The reference sensor used for the heat metering is set here.

Settings range: S1-S8, VFS1-2, active collector, active storage/ Default setting: S1

-----------------------------------------------------------------------------------

6.6. - Pressure monitor 

 

 

 

menu 6.6

A message is shown when the pressure drops below set minimum or exceeds the set maximum pressure. No 
relay is switched, for that see „6.4.12. - Pressure monitor“ on page 43.

6.6.1. - Pressure monitor   

 

 

menu 6.6.1

A message is shown and the LED 

fl

ashes when the pressure deviates from the set minimum or maximum 

value.

Default setting: On, Off / Výchozí nastavení: Off

6.6.1.1. - RPS1 / RPS2 

 

 

 

menu 6.6.1.1

Type of pressure sensor

 

 This menu is used to determine the type of pressure sensor used.

Please note: 

If e.g. VFS1 is connected, RPS1 option is not shown.

Settings range: Off; 0-0.6 bar; 0-1 bar; 0-1.6 bar; 0-2.5 bar; 0-4 bar; 0-6 bar; 0-10 bar
Default setting: Off

6.6.1.2. 

– 

Pmin 

    

menu 6.6.1.2

Minimum pressure

If this value is undershot, an error message is displayed and the relay is switched on.

Settings range: Off; 0,0 to 1.6 bar
Default setting: 0,0bar

6.6.1.3. 

Pmax 

    

menu 6.6.1.3

Maximum pressure

If this value is exceeded, an error message is displayed and the relay is switched on.

Settings range: Off; 0,0 to 10 bar
Default setting: 1.6 bar

Danger

Содержание SRS6

























































Отзывы: