Regency liberty LRI3E, Инструкция для владельца и по установке

Страница: 17 / 56

LRI3E / HRI3E Direct Vent Gas Insert
|
17
|
17
installation
GAS PIPE PRESSURE
TESTING
The appliance must be isolated from the gas sup-
ply piping system by closing its individual manual
shut-off valve during any pressure testing of the
gas supply piping system at test pressures equal
to or less than 1/2 psig. (3.45 kPa). Disconnect
piping from valve at pressures over 1/2 psig.
The manifold pressure is controlled by a regulator
built into the gas control, and should be checked
at the pressure test point.
Note: To properly check gas pressure, both
inlet and manifold pressures should be
checked using the valve pressure ports
on the valve.
1) Make sure the valve is in the "OFF" position.
2) Loosen the "IN" and/or "OUT" pressure tap(s),
turning counterclockwise with a
1/8" wide lat screwdriver.
3) Attach manometer to "IN" and/or "OUT" pressure
tap(s) using a 5/16" ID hose.
4) Light the unit using the supplied hand held
remote control. (See lighting procedure in this
manual).
5)
The pressure check should be carried out with
the unit burning and the setting should be within
the limits speciied on the safety label.
6) When inished reading manometer, turn off the
gas valve, disconnect the hose and tighten the
screw (clockwise) with a 1/8" lat screwdriver.
Note: Screw should be snug, but do not over
tighten.
HIGH ELEVATION
This unit is approved for altitude 0 to 4500 ft. (CAN1
2.17-M91).
GAS LINE
INSTALLATION
Since some municipalities have additional local
codes it is always best to consult with your local
authorities and the CAN/CGA B149 installation
code.
For USA installations follow local codes and/or the
current National Fuel Gas Code, ANSI Z223.1.
When using copper or lex connectors use only
approved ittings. Always provide a union so that
gas lines can be easily disconnected for servicing.
Flare nuts for copper lines and lex connectors are
usually considered to meet this requirement.
NOTE: A shutoff / dante valve should be sup-
plied in or near the unit (or as per local codes)
for ease of servicing this appliance.
IMPORTANT: Always check for gas leaks with
a soap and water solution or gas leak detector.
Do not use open lame for leak testing.
LRI3E-NG / HRI3E-NG
SYSTEM DATA
Max. Supply Pressure 14'' WC (3.45 kpa)
Min. Supply Pressure 5.5" WC (1.37 kpa)
Manifold Pressure 3.8" WC (0.95 kpa)
Oriice Size
#45 DMS
Maximum Input 21,000 Btu/h
(6.15 kW)
LRI3E-LP / HRI3E-LP
SYSTEM DATA
Max. Supply Pressure 14'' WC (3.45 kpa)
Min. Supply Pressure 11" WC (2.73 kpa)
Manifold Pressure 10.6" WC (2.64 kpa)
Oriice Size
#55 DMS
Maximum Input 21,000 Btu/h
(6.15 kW)
Note: If you have an incorrect lame pattern,
contact your Regency
®
dealer for further
instructions.
Incorrect lame pattern will have small, probably
yellow lames, not coming into proper contact
with the rear burner or lame sensor.
Burner
Thermocouple
Pilot
Ignitor
GV60 MAXITROL VALVE
DESCRIPTION
1) Manual Knob
2) Pressure regulator
3) Main Valve Knob
4) Minimum Rate Oriice
5) Bottom Inlet
6) Bottom Outlet
7) Outlet Pressure Tap
8) Inlet Pressure Tap
9) Side Outlet
10) Side Inlet
1
3
10
9
8
7
6
5
2
4