Regency Grandview G800C Скачать руководство пользователя страница 64

Страница: 64 / 92

Grandview® G800C Gas Fireplace

installation

Log Set installation

11.22.19

920-127a

LOG SET INSTALLATION

Page 1 of 4

Rear Log

Middle Left Log

Middle Right Log

Center Left Cross Log

Front Bottom 'Y' Log

Left Rear Log

Right Cross Log

Middle Front

Left Log Piece

Right Log Piece

Left Front Log Piece

Right Front Log Piece

Must also purchase (#761-938) Log
Grate and Ember package separate-
ly. The kit contains:

Log Grate

3/4" Ginger glass

Vermiculite

Black/White Embers

Log Support Plates

Read the instructions below carefully and refer to the diagrams.
If logs are broken do not use the unit until they are replaced.
Broken logs can interfere with the pilot operation.

The G800EC/G800C log sets, #761-930 for Oak, #761-932 for Birch,
contain the following pieces:

NOTE: Panels (brick, steel, or enamel) must be installed

prior to installing the log set.

1. Carefully remove the logs from the box and unwrap them. The logs

are fragile, handle with care -

do not force into position when

installing.

2. Install the log grate—secure with 2 screws in locations show below.

3. Install the supplied crystals over the ember lights underneath the

burner as shown. Place vermiculite and embers on top of the glass.
Do not place any media on the burner.

Diagram 1—Log ID

Diagram 2—Log Grate Install

Diagram 3—Install Glass

Diagram 4—Install Vermi Lava

G800EC/G800C

Содержание Grandview G800C





























































































Результаты поиска

Содержание Grandview G800C

Отзывы:

Похожие инструкции для Grandview G800C

Бренды по названию

Популярные бренды

Regency Grandview G800C, Инструкция для владельца и по установке

Результаты поиска

Содержание Grandview G800C

Отзывы:

Похожие инструкции для Grandview G800C

Бренды по названию

Популярные бренды