Regency Grandview G800C Скачать руководство пользователя страница 34

Страница: 34 / 92

Grandview® G800C Gas Fireplace

installation

08.28.19

920-151

FINISHING TRIM INSTALLATION

The Finishing Trim can be installed to upgrade the look of the fi replace
or to cover facing material edges.

1. Lay the parts on a soft surface painted side down.

2. Insert the tab on the left side into the slot on the top.

3. Fold the tabs down to secure.

4. Insert the tab on the top into the slot on the right.

5. Fold the tab down to secure.

Right Side

Finishing Trim Install Instructions:

1. Bend the four tabs on the outer box front forward. There are two tabs per side.

These tabs are the mounts for the faceplate or fi nishing trim.

2. Bend the two tabs on the top nailing fl ange down.

3. Bend the tabs on the left and right nailing fl anges forward. There are two tabs

per nailing fl ange.

Top and Side Nailing Flange Tabs

See section: N

AILING

LANGE

NSTALL

FOR

AILING

LANGE

EPTH

SETTINGS

Left Side

Finishing Trim Install

Top and Side Nailing Flange Tabs

Содержание Grandview G800C





























































































Результаты поиска

Содержание Grandview G800C

Отзывы:

Похожие инструкции для Grandview G800C

Бренды по названию

Популярные бренды

Regency Grandview G800C, Инструкция для владельца и по установке

Результаты поиска

Содержание Grandview G800C

Отзывы:

Похожие инструкции для Grandview G800C

Бренды по названию

Популярные бренды