Regency Grandview G800C Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 92

background image

Grandview® G800C Gas Fireplace

| 3

MANUFACTURED MOBILE HOME REQUIREMENTS

INFORMATION FOR MOBILE/MANUFACTURED HOMES AFTER FIRST SALE

This Regency

®

product has been tested and listed by Intertek as a Direct Vent Wall Furnace to the following

standards: Vented Gas Fireplace Heaters ANSI Z21.88-2017.

This Direct Vent System Appliance must be installed in accordance with the manufacturer's installation instructions
and the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, or the current Standard
of Fire Safety Criteria for Manufactured Home Installations, Sites, and Communities ANSI/NFPA 501A.

This appliance installation must comply with the manufacturer's installation instructions and local codes, if any.
In the absence of local codes follow the current National Fuel Gas Code, ANSI Z223.1 and the current National
Electrical Code ANSI/NFPA 70 in the U.S.A.

This appliance comes equipped with a dedicated #8 Ground Lug for attachment of the ground wire to the steel
chassis as applicable to local codes.

The appliance, when installed, must be electrically grounded in accordance with local codes or, in the absence of
local codes, with the National Electrical Code, ANSI/NFPA 70.

This appliance may only be installed in an aftermarket permanently located, manufactured (U.S.A only) or mobile
home, where not prohibited by local codes.

This appliance can only be used with the type of gas indicated on the rating plate. This appliance is not convertible
for use with other gases.

Ensure that structural members are not cut or weakened during installation.

This appliance may be installed in an aftermarket permanently
located, manufactured (U.S.A. only) or mobile home, where
not prohibited by local codes.

This appliance is only for use with the type of gas indicated on
the rating plate. A conversion kit is supplied with the appliance.

«
1
2
3
4
5
...
»

Содержание Grandview G800C





























































































Отзывы:

Нет отзывов

Похожие инструкции для Grandview G800C

Бренд: Pacific energy Страницы: 60

Бренд: Pacific energy Страницы: 40

SUPER INSERT DESIGN-E SPNE

Бренд: Pacific energy Страницы: 24

Бренд: HAMPTONBAY Страницы: 30

Бренд: Astria Страницы: 24

Бренд: FocalPoint Страницы: 5

Бренд: Lopi Страницы: 3

Бренд: Vermont Castings Страницы: 48

Бренд: Enviro Страницы: 47

FireBrick Gas Insert ADI-ZCFB-S

Бренд: Heatilator Страницы: 2

Бренд: La Hacienda Страницы: 4

Бренд: Desa Страницы: 28

Бренд: Canvas Страницы: 100

Бренд: HAMPTON BAY Страницы: 48

Бренд: Woodbridge Fireplace Inc Страницы: 20

Бренд: KALOS Страницы: 20

Бренд: Lamborghini Caloreclima Страницы: 116

Бренд: Warmlite Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды