Regency CB40E-LP11 Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 88

background image

CV40E-11 City Series

|

59

installation

CV40E Glass Panel Installation

919-657a

02.22.17

CV40E GLASS PANEL INSTALLATION

1. Turn off unit and allow to cool to room temperature. Remove the safety glass

and firebox glass — see manual for instructions.

Note:

The screws to secure all of the clips in these instructions will be already

be on the appliance. Simply remove and reinstall to secure all of the clips.

2. Identify panels and order of installation.

1

2

5

4

6

1

*3 (2 pieces)

7

1

side panel

outer front panel

outer side panel

side panel bracket

back corner panel

metal panel

glass panel sitting on top of

metal panel installed in previous

step

3. Install back corner panels (1, 2) - seat smallest panel in back left corner,

repeat on other side.

5. Install metal panel (3) into of front firebox panel.

7. Install one of the back panel brackets loosely with one screw (leave the

bracket loose to allow room to install the back panel behind it).

8. Carefully manoeuvre the back glass panel (4) to the back wall of the firebox.

Centre the glass panel at the back of the firebox positioning underneath the
loosely installed bracket— once in position, slide the bracket in position on
the opposite side and tighten both brackets in place with one screw each.

9. With the back panel installed, slide in one of the side glass panels (6). Push

the panel all the way to the back of the firebox ensuring that the glass is sitting
on the bottom corner bracket installed in step 4. Attach top rear bracket as
shown. Note: There is a left and right bracket. The left bracket is shown below.

13. Install outer front panel (1) as shown. Secure Regency logo to underside

of outer front panel. The logo is simply held in with magnets.

15. Reinstall the Outer Safety Glass

*Panel 3 - 1 metal panel
- 1 glass panel

4. Install bottom corner 'securing bracket' as shown. Repeat step for other side.

Securing bracket

Securing bracket in place

Panel 1 shown

6. Install glass panel (3) on top of the metal panel.

11. Repeat steps 9-10 for other side. Clean all fingerprint marks prior to next step.

12. Install media and inner firebox glass prior to next step.

14. Install outer side panels (8, 9) —these panels are held in position with

magnets. Clean all fingerprint marks on outer side and bottom panels
prior to next step.

Top rear

bracket

sitting

on top of

side glass

panel.

10. Install side panel bracket as shown and secure with one screw.

back panel bracket

back glass panel (4)

location of

Regency logo

at bottom right

corner

Top rear bracket

tucked in behind

back glass panel

1

CITY SERIES

«
...
57
58
59
60
61
...
»

Содержание CB40E-LP11

























































































Отзывы:

Нет отзывов

Похожие инструкции для CB40E-LP11

Бренд: Sunjoy Страницы: 5

Бренд: Sunnydaze Decor Страницы: 2

Бренд: HAMPTON BAY Страницы: 17

Бренд: Uniflame Страницы: 8

Бренд: Martin Страницы: 36

Бренд: Lennox Hearth Products Страницы: 30

Wall Mantel with Base and Trim WD26CP

Бренд: Desa Страницы: 8

L-OF083PST-2 Bel Aire

Бренд: Sunjoy Страницы: 4

Бренд: SEI Страницы: 8

Бренд: Heatilator Страницы: 88

739CLK Classic Log Kit

Бренд: Valor Страницы: 4

Бренд: Focal Point Страницы: 17

Бренд: Charlton & Jenrick Страницы: 24

Бренд: UrbanFire Страницы: 20

Бренд: Procom Страницы: 16

Бренд: Godin Страницы: 14

Бренд: Outdoor Lifestyles Страницы: 29

Fire Island GAD15410M

Бренд: MR. BAR-B-Q Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды