manualshive.com logo in svg

Regency CB40E-LP11, Инструкция для владельца и по установке

"Regency CB40E-LP11" - газовый камин с отличным дизайном и высоким качеством. Для правильной эксплуатации и установки необходимо ознакомиться с инструкцией пользователя и руководством по установке. Вы можете бесплатно загрузить их с manualshive.com. Удобство и безопасность вашего камина гарантированы.

Поделиться
Скачать
background image

 

CV40E-11 City Series

  |    

5

safety decal

This is a copy of the label that accompanies Direct Vent Gas Fireplace. We have printed a copy of the contents here for your review. The safety label is located 
on the front inside base of the unit, visible when the outer front panel is removed.

NOTE: Regency

®

 units are constantly being improved. Check the label on the unit and if there is a difference, the label on the unit is the correct one.

Copy of Safety Decal

For the State of Massachusetts, installation 
and repair must be done by a plumber or 
gas fitter licensed in the Commonwealth of 
Massachusetts.

For the State of Massachusetts, flexible con-
nectors shall not exceed 36 inches in length.

For the State of Massachusetts, the appli-
ances individual manual shut-off must be a 
t-handle type valve.

The  State  of  Massachusetts  requires  the 
installation of a carbon monoxide alarm in 
accordance with NFPA 720 and a CO alarm 
with battery back up in the same room where 
the gas appliance is installed.

Part #:   

919-929a

Colour:  

Black on grey except what is indicated as being printed red.

Size:   

(File at 100%)  9.18"W x 6.198"H

Material:  

Oct. 15/18: 

Created draft

Nov. 05/18: 

New Serial #

Nov 20/18: 

Added efficiencies as per R/D

Jan 23/19: 

Rev A - Remodeled decal + added ETL logo at the bottom

DO NOT REMOVE THIS LABEL /

NE PAS ENLEVER CETTE ÉTIQUETTE

                     

484

484

DOOR SEAL: Please 

check that the door is 

properly sealed

FPI Fireplace Products International Ltd. Delta, BC, Canada

Minimum Clearances to Combustibles /

Dégagements minimaux par rapport aux matériaux combustibles

Serial No./ No de série

919-929a

MAY BE INSTALLED IN MANUFACTURED (MOBILE) HOMES AFTER FIRST SALE

.

Listed/Nom:

 VENTED GAS FIREPLACE HEATERS  / APPAREIL DE CHAUFFAGE AU GAZ À ÉVACUATION.

Certified to/Certifi  : 

é

 ANSI Z21.88-2017 • CSA-2.33-2017

                                             CSA 2.17-2017

Electrical supply / Alimentation électrique  115VAC, 1.5 A, 60Hz.

   

Made in Canada/ Fabriqué au Canada

Duplicate S/N

(

See Instruction Manual for detailed instructions)

(Voir manuel pour plus de détails)

APPAREIL FONCTIONNANT AU GAZ PROPANE

Modèle 

CV40E-LP11/CB40E-LP11

PROPANE GAS: Model: CV40E-LP11/CB40E-LP11

       

NATURAL GAS: Model: CV40E-NG11/CB40E-NG11

Minimum supply pressure

Manifold pressure - High

Manifold pressure - Low

Orifice size

Maximum input

Minimum input

Altitude

APPAREIL FONCTIONNANT AU GAZ NATUREL 

Modèle 

CV40E-NG11/CB40E-NG11

5.0"           WC/C.E.   (1.25 kPa)

3.8"           WC/C.E.   (0.94 kPa)

1.1"        WC/C.E. (0.27 kPa)

# 42                     DMS      

28,500   Btu/h  (8.33 kW)

15,500   Btu/h  (4.54 kW)

0-4500       ft/pi          (0-1372 m)

11"        WC/C.E. (2.73 kPa)

10.5"     WC/C.E.  (2.62 kPa)

2.9"       WC/C.E.  (0.72 kPa)

# 53                   DMS   

28,500  Btu/h  (8.35kW)

15,500  Btu/h  (4.54 kW)

0-4500      ft/pi         (0-1372 m)

         

Minimum supply pressure

Manifold pressure - High

Manifold pressure - Low

Orifice size

Maximum input

Minimum input

Altitude

D

E

F

A

B

C

Side Walls / Murs latéraux

A   8.5” (216 mm)

Ceiling / Plafond

B              37-1/2”  (953 mm)

Min. Mantel Height

 

/Hteur Min 

Manteau

C   9"  (229 mm) with 12” mantel

Max. Mantel Depth/Profondeur Max 

Manteau

D   12”  (305 mm) 

Alcove Width/Largeur Alcôve

E   84"  (1524 mm)

Alcove Depth/Profondeur Alcôve

F   36"  (2134 mm)

This appliance must be installed in accordance with local codes, if any; if none, follow the National Fuel Gas Code, ANSI Z223.1, or Natural Gas and Propane Installation Code, CSA B149.1.

This appliance must be installed in accordance with the Standard CAN/CSA Z240 MH, Mobile Housing, in Canada, or with the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, in the 

United States, or when such a standard is not applicable, ANSI/NCSBCS A225.1/NFPA 501A, Manufactured Home Installations Standard or ANSI  A119.2 ou NFPA 501C Standard for Recreational Vehicles

This appliance is only for use with the type(s) of gas indicated on the rating plate and may be installed in an aftermarket, permanently located, manufactured home (USA only) or mobile home, where not prohibited by 

local codes. See owner's manual for details. This appliance is supplied with a conversion kit.

L'appareil doit être installé conformément aux codes et règlements locaux, ou, en l'absence de tels règlements, selon les codes d'installation National Fuel Gas Code ANSI Z223.1, ou CSA-B149.1 Natural Gas and 

Propane Installation Code en vigueur.

L'appareil doit être installé conformément à la norme CAN/CSA-Z240, Série MM, Maisons mobiles ou CAN/CSA-Z240 VC, Véhicules de camping, ou la norme 24 CFR Part 3280, Manufactured Home Construction 

and Safety Standard. Si ces normes ne sont pas applicables, veuillez vous référer à la norme ANSI/NCSBCS A225.1/NFPA 501A, Manufactured Home Installations Standard, ou ANSI A119.2 ou NFPA 501C 

Standard for Recreational Vehicles.

Cet appareil doit être utilisé uniquement avec les types de gaz indiqués sur la plaque signalétique et peut être installé dans une maison préfabriquée (É.-U. seulement) ou mobile installée à demeure si les règlements 

C #: 4001172

For Use Only with Barrier CV40E - 1 sided (Part # 940-435/P) & CB40E 3 sided (Part # 940-438/P,940-439/P,940-440/P) Follow installation instructions. 

Utiliser uniquement avec l’écran CV40E -1 face (n°940-435/P) & CB40E - 3 faces (n°940-438/P,940-439/P,940-440/P) . Suivre les instructions d'installation.

Pression d'alimentation minimale

Pression de sortie (manifold) - Haute

Pression de sortie (manifold) - Basse

Taille de l’orifice

D bit calorifique maximal 

é

D bit calorifique minimal

é

Altitude

Pression d'alimentation minimale

Pression de sortie (manifold) - Haute

Pression de sortie (manifold) - Basse

Taille de l’orifice

D bit calorifique maximal

é

D bit calorifique minimal

é

Altitude

VENTED GAS FIREPLACE  - NOT FOR USE WITH SOLID FUELS. 

NE PAS UTILISER AVEC UN COMBUSTIBLE SOLIDE. 

FOYER AU GAZ À ÉVACUATION - 

Part No. 946-556 Heatwave Kit may be used.   Le système Heatwave (pièce n°946-556) peut être utilisé

.

Model/Modèle :       

CV40E-NG11

  

   

CV40E-LP11

      

 

CB40E-NG11

     

 

CB40E-LP11  

     

FOR USE WITH GLASS DOORS CERTIFIED WITH THE APPLIANCE ONLY     À UTILISER AVEC LES PORTES VITRÉES HOMOLOGUÉES POUR L'APPAREIL 

Min. 120in²

Refer to Intertek's Directory of Building Products for detailed information.

Pour plus de détails, se reporter au Répertoire des produits de construction de Intertek. 

CSA P.4.1 Fireplace Efficiency (FE) /Efficacité énergétique des foyers (EEF) CSA P.4.1

Natural Gas / Gaz naturel 55.23%

Propane Gas / Gaz propane 56.06%

CANADIAN ENERGY 

PERFORMANCE 

VERIFIED

RENDEMENT 

ÉNERGÉTIQUE 

VÉRIFIÉ

EP5011169

Decal Location

Remove barrier glass from unit (refer to manual) 
lift out the outer liner base glass once the glass 
has been removed the rating plate will be attached 
to a small black chain as seen below.

DO NOT REMOVE DECAL FROM UNIT

Содержание CB40E-LP11

























































































Отзывы:

Нет отзывов

Похожие инструкции для CB40E-LP11

HAMPTON BAY MTVS2500S Use And Care Manual preview
MTVS2500S
Бренд: HAMPTON BAY Страницы: 36
Be Modern Elgin & Hall Installation Instructions And User Manual preview
Elgin & Hall
Бренд: Be Modern Страницы: 8
LA NORDICA Crystal 50v Instructions For Installation, Use And Maintenance Manual preview
Crystal 50v
Бренд: LA NORDICA Страницы: 76
Vermont Castings Brookhaven 20DVT Installation Instructions And Homeowner'S Manual preview
Brookhaven 20DVT
Бренд: Vermont Castings Страницы: 32
Valor 780MN Installation Manual preview
780MN
Бренд: Valor Страницы: 46
White Mountain Hearth PONDEROSA LS-24P-1 Installation Instructions And Owner'S Manual preview
PONDEROSA LS-24P-1
Бренд: White Mountain Hearth Страницы: 12
Napoleon BGD42 Installation And Operation Instructions Manual preview
BGD42
Бренд: Napoleon Страницы: 28
ELEMENTI OFP121BB Owner'S Manual preview
OFP121BB
Бренд: ELEMENTI Страницы: 60
Klarstein Zermatt 10033051 Manual preview
Zermatt 10033051
Бренд: Klarstein Страницы: 44
Vermont Castings LHEACNSS Contour KT1B80 Installation Instructions preview
LHEACNSS Contour KT1B80
Бренд: Vermont Castings Страницы: 2
Heta SCAN-LINE 80 Operating And Installation Instructions preview
SCAN-LINE 80
Бренд: Heta Страницы: 20
Endless Summer Emerson GAD15412SP Owner'S Manual preview
Emerson GAD15412SP
Бренд: Endless Summer Страницы: 22
Evonicfires Ev4i Instruction Manual preview
Ev4i
Бренд: Evonicfires Страницы: 20
Boulevard VFLL60SP90LN-1 Installation Instructions Manual preview
VFLL60SP90LN-1
Бренд: Boulevard Страницы: 48
Superior Fireplaces VRE4543E Installation & Operation Instructions preview
VRE4543E
Бренд: Superior Fireplaces Страницы: 32
UKIAH TAILGATER Manual preview
TAILGATER
Бренд: UKIAH Страницы: 24
Coleman 5059A703 Assembly And Instruction Sheet preview
5059A703
Бренд: Coleman Страницы: 2
COUNTRY FLAME TECHNOLOGIES IN-6200 Installation, Operation And Maintenance Manual preview
IN-6200
Бренд: COUNTRY FLAME TECHNOLOGIES Страницы: 10

Бренды по названию

Популярные бренды

Загрузить еще бренды