Regency CB40E-LP11 Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 88

background image

CV40E-11 City Series

|

53

installation

Inner Glass Panel (Firebox Glass) Installation / Removal

1. Remove outer safety glass panels if previously installed–see instructions

in this manual.

2. Remove outer panels installed in units - see panel removal section in this

manual.

3. Ensure all 7 front clamps are in the open position to allow clearance for

the glass.

Important:

Prior to installing the inner glass, ensure that there is no media present in
the bottom channel as this can cause damage to the glass. Remove any
media from bottom channel prior to installing the glass.

WARNING: GLASS HANDLING

We recommend using the glass vacuum holders supplied by the manufac-
turer. Lower the glass to rest in a safe place, this is to prevent damage to the
glass edges. Extra care must be taken when removing/installing the glass.
Breakage or damage to the edge of the glass which occurs as a result of
careless handling will not be covered under warranty.

•

We recommend handling the glass with supplied vacuum
clamps

• When removing glass–prepare a soft, scratch resistant

surface to place the glass

• Never clean or remove hot glass
Note: The suction cups may leave a round film on the glass
when used. Ensure that the glass is cleaned using a fireplace
glass cleaner prior to operating the appliance.

Note:

glass panels must be installed to operate fireplace

To watch the firebox installation video click

here.

Handle front panel with supplied vacuum clamps

Open 7
clamps prior
to placing
front glass
panel

4. Lift up the front panel using the supplied vacuum clamps and position into

the lower front channel–ensure the front panel is accurately centered—with
the front panel in position—secure in place by closing the 3 lower clamps
and 4 upper clamps.

Press glass vacuum clamps in open position firmly onto surface of glass. Bring
handles together to close.

Closed

Open

5. To remove the glass panels—always remove the side panel(s) (for 3 sided

units) before removing the front panel.

6. Reverse steps to remove glass.

«
...
51
52
53
54
55
...
»

Содержание CB40E-LP11

























































































Отзывы:

Нет отзывов

Похожие инструкции для CB40E-LP11

Бренд: Pacific energy Страницы: 20

CGCDV36NR SERIES

Бренд: Desa Страницы: 44

Paul Agnew Designs ilektro Series

Бренд: Living Fire Страницы: 4

Бренд: Twin-Star International Страницы: 19

Бренд: Travis Industries Страницы: 8

Бренд: Valor Heating Страницы: 42

Бренд: Piazzetta Страницы: 40

Бренд: Napoleon Страницы: 3

Бренд: Majestic Страницы: 79

Бренд: KEKAI Страницы: 98

Бренд: ELEMENTI Страницы: 20

Бренд: La Hacienda Страницы: 4

Бренд: Oranier Страницы: 52

Бренд: Char-Broil Страницы: 4

IronStrike Performer C210AGL

Бренд: IHP Страницы: 28

RUTHERFORD 50-B

Бренд: Heat&Glo Страницы: 48

Бренд: Heat&Glo Страницы: 56

Бренд: Pacific energy Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды