Regency CB40E-LP11 Скачать руководство пользователя страница 22

Страница: 22 / 88

CV40E-11 City Series

installation

Caution Requirements

The top, back and sides of the fireplace are defined by

standoffs. The metal ends of the standoff may

NOT

recessed into combustible construction.

WARNING

Fire hazard is an extreme risk

if these clearances (air space) to combustible materials are not

adhered to. It is of greatest importance that this fireplace and vent

system be installed only in accordance with these instructions.

Clearances CV40E

The clearances listed below are Minimum distances unless otherwise stated:

A major cause of chimney related fires is failure to maintain required clearances (air space) to combustible materials. It is of the greatest importance that this
fireplace and vent system be installed only in accordance with these instructions.

Clearance: single sided

Dimension

Measured From:

A: Mantel Height (min.)

Top of Fireplace Opening

B1: From Floor

Min. 0"

Bottom of Fireplace Opening

B2: Opening Height

15-1/16" (383mm)

Bottom/Top of Fireplace Opening

C: Sidewall (on one side)

8-1/2" (216mm)

Side of Fireplace Opening

D: Mantel Depth (max.)

E: Alcove Width

84" (2134mm)

Sidewall to Sidewall (Minimum)

F: Alcove Depth

36" (914mm)

Front to Unit (Maximum)

G: Ceiling
(in front of fireplace)

37-1/2" (953mm)

Top of Fireplace Opening

H: Convection Air Outlet

Top of Enclosure

J: Convection Air Outlet Opening Offset

0-3" (76mm)

Max. offset from top of chase enclosure

K: Chase Enclosure (Min.)

63" (1600mm)

From base of unit/floor

L: Clearance to Sprinkler Head (Min.)

36" (914mm)

Perpendicular from chase grill

Hearth

No hearth required

** See mantel clearances chart in this manual.

Flue Clearances to Combustibles

Horizontal - Top

Horizontal - Side

Horizontal - Bottom

Vertical

Passing through wall/
floor/ceiling - when
firestop is used.

1-1/2"

Alcove

The

HeatWave

Duct Kit has differ-

ent clearance and framing require-
ments, check the

HeatWave

manual

for details.

CV40E- Single sided

A minimum of 120 square

inches of open area, not
lower than 3" from top of
enclosure, required for all
installations

Chase grill

Sprinkler

Side view

Содержание CB40E-LP11

























































































Результаты поиска

Содержание CB40E-LP11

Отзывы:

Похожие инструкции для CB40E-LP11

Бренды по названию

Популярные бренды

Regency CB40E-LP11, Инструкция для владельца и по установке

Результаты поиска

Содержание CB40E-LP11

Отзывы:

Похожие инструкции для CB40E-LP11

Бренды по названию

Популярные бренды