manualshive.com logo in svg

Regency CB40E-LP11, Инструкция для владельца и по установке

"Regency CB40E-LP11" - газовый камин с отличным дизайном и высоким качеством. Для правильной эксплуатации и установки необходимо ознакомиться с инструкцией пользователя и руководством по установке. Вы можете бесплатно загрузить их с manualshive.com. Удобство и безопасность вашего камина гарантированы.

Поделиться
Скачать
background image

4

    | 

CV40E-11 City Series

table of contents

Owner's Information

Installer's Information

Locating Your Gas Fireplace ........................................19
Unit Assembly Prior to Installation ...............................19
General Safety Information ..........................................21
Installation Checklist ....................................................21
Heatwave Duct System ...............................................21
Clearances CV40E ......................................................22
Mantel Clearances CV40E ..........................................23
Mantel Leg Clearances ................................................23
Framing Dimensions CV40E .......................................24
Chase Vent Installation ................................................25
Chase Venting .............................................................28
Optional Front Grill Installation ....................................29
Wall Board/Drywall Installation ....................................30
Framing and Finishing Inset Installations CV40E ........31
TV Recessed into Wall ................................................32
Maximum TV Recess ...................................................32
TV Flush with Hearth ...................................................32
Exterior Vent Termination Locations ............................33
4” x 6-5/8” Rigid Pipe Cross Reference Chart .............34
Wall Mount On / Off Switch / Battery Holder  ..............36
Vent Restrictor Position ...............................................37
Horizontal Terminations ...............................................38
Venting Introduction .....................................................39
Venting Arrangement for Horizontal Terminations .......39
Horizontal Terminations ...............................................40

Copy of Safety Decal .....................................................5
Important Message   ......................................................7
Before You Start .............................................................7
General Safety Information ............................................8
Lighting Procedure ........................................................9
Shutdown Procedure .....................................................9
Copy of the Lighting Plate Instructions ........................10
Proflame II Remote Control Operating Instructions .....11
Inner Glass Panel (Firebox Glass) ..............................15
Outer Safety Glass Panel (Barrier Glass) ....................16
Maintenance Instructions ............................................17
General Vent Maintenance ..........................................17
Log Replacement ........................................................17
Glass Gasket ...............................................................17
Glass ...........................................................................17
Glass Replacement .....................................................17

Warranty .....................................................................80

Vertical terminations ....................................................42
Venting Arrangement for Vertical Terminations ............43
Vertical Terminations  Rigid Pipe 4" x 6-5/8" ...............44
Unit Installation with Horizontal Termination  ...............45
Unit Installation with Horizontal Termination  ...............46
Dura-Vent Horizontal Terminations ..............................47
Dura-Vent Vertical Termination ....................................48
Vertical Termination  
4" x 6-7/8" Venting - Vertical Flex Vent Kit (946-755) ...49
Vertical Flue Extension Kit (Part #946-756).................50
Ceiling Firestop / Firestop Spacer (Part #946-757) .....50
High Elevation ..............................................................51
Gas Line Installation ....................................................51
Pilot Adjustment ...........................................................51
Gas Pipe Pressure Testing ..........................................51
885 S.I.T. Valve Description .........................................51
Wiring Diagrams ..........................................................52
Inner Glass Panel (Firebox Glass) Installation ............53
Outer Safety Glass Panel (Barrier Glass)  ...................54
LP Conversion Instructions ..........................................55
Clean Trim Faceplate Installation .................................57
CV40E Painted Panel Installation ................................58
Inner Panels-CV40E ....................................................58
Outer Panels-CV40E ...................................................58
CV40E Glass Panel Installation ...................................59
CV40E Enamel Panel Installation ................................60
Extended View Panel Installation .................................61
Burner and Firebox Media Options ..............................63
Optional Driftwood Log Set Installation .......................64
Optional Birchwood Log Set Installation ......................66
Optional Splitwood Log Set Installation .......................68
TV Kit Installation  ........................................................70
First Fire ......................................................................72
Normal Operating Sounds Of Gas Appliances ............72
Aeration Adjustment ....................................................72
Maintenance Instructions ............................................73
General Vent Maintenance ..........................................73
Log Replacement ........................................................73
Glass Gasket ...............................................................73
Glass ...........................................................................73
Glass Replacement .....................................................73
Bulb Replacement .......................................................74
Valve Replacement ......................................................75
Gas Maintenance ........................................................76
CV40E Main Assembly ................................................77
CV40E Main Assembly ................................................78

Warranty .....................................................................80

Содержание CB40E-LP11

























































































Отзывы:

Нет отзывов

Похожие инструкции для CB40E-LP11

Napoleon Vector Series Installation Manual preview
Vector Series
Бренд: Napoleon Страницы: 156
Regency Fireplace Products P90-LP10 Owners & Installation Manual preview
P90-LP10
Бренд: Regency Fireplace Products Страницы: 52
Luxor MB-36 Installation And Owner'S Manual preview
MB-36
Бренд: Luxor Страницы: 25
Napoleon GD19-1N Installation And Operating Instructions Manual preview
GD19-1N
Бренд: Napoleon Страницы: 128
Safavieh Furniture Antigua PIT1015A Manual preview
Antigua PIT1015A
Бренд: Safavieh Furniture Страницы: 3
Valcourt DALLAIRE FP18 Installation And Operation Manual preview
DALLAIRE FP18
Бренд: Valcourt Страницы: 70
UBERHAUS DESIGN 83035033 WW11994 Operator'S Manual preview
83035033 WW11994
Бренд: UBERHAUS DESIGN Страницы: 11
Charlton & Jenrick 2000 Plus Extra Remote Owner'S Manual preview
2000 Plus Extra Remote
Бренд: Charlton & Jenrick Страницы: 32
IHP RIVROCK-25PK Installation Instructions preview
RIVROCK-25PK
Бренд: IHP Страницы: 2
IHP 900005-02 Installation Instructions preview
900005-02
Бренд: IHP Страницы: 4
Lifepro LS1111HH Installation Instructions Manual preview
LS1111HH
Бренд: Lifepro Страницы: 15
EDYO LIVING ZHX-23-040 Use And Care Manual preview
ZHX-23-040
Бренд: EDYO LIVING Страницы: 11
Heat&Glo Montana-36 Owner'S Manual preview
Montana-36
Бренд: Heat&Glo Страницы: 40
Outdoor Lifestyles TWILIGHT-II-MOD Installation Manual preview
TWILIGHT-II-MOD
Бренд: Outdoor Lifestyles Страницы: 28
Duluth Forge FDLR24 Owner'S Operation And Installation Manual preview
FDLR24
Бренд: Duluth Forge Страницы: 32
Klarstein 10035202 Manual preview
10035202
Бренд: Klarstein Страницы: 32
Quadra-Fire EXPLR-I-MBK Installation Manual preview
EXPLR-I-MBK
Бренд: Quadra-Fire Страницы: 20
Quadra-Fire EXPEDITION II Installation Manual preview
EXPEDITION II
Бренд: Quadra-Fire Страницы: 28

Бренды по названию

Популярные бренды

Загрузить еще бренды