Regency Fireplace Products U39-NG12, Инструкция для владельца и по установке

Страница: 21 / 60

Regency
®
U39-12 ULTIMATE™ Freestanding Gas Stove
| 21
installation
Outside
Wall
Mur extérieur
Furring
Strips
Fourrures en bois
Furstrp.eps
see also c34020a.eps
furstrpf.eps
french
Dismantle all pipe sections including vent terminal.
3. Attach the 4" dia. flex liner to the vent terminal
ensuring that the flex overlaps the collar of the
vent terminal by a minimum of 1-3/8"(35mm).
Use Mill-Pac to seal and secure with 3 of the
#8 x 1/2" screws (stainless steel).
4. Attach the adjustable pipe section to the vent
terminal using Mill-Pac and attach with 3 of
the #8 x 1/2" screws (stainless steel).
Note: The pipe seam should be facing
down.
Note: To make the installation more
a e s t h e t i c a l ly p l e a s i n g , w e
recommend framing out a square
that the cap can be mounted on.
Note: If installing termination on a siding
covered wall, a vinyl siding standoff
or furring strips must be used to
ensure that the termination is not
recessed into the siding.
9. Secure the 4" dia. flex liner to the 4" adapter with
Mill-Pac and 3 of the #8 x 1/2" screws (stainless
steel).
10. Slide the decorative Thimble Cover over the
pipe sections and secure with 4 screws (#8 x
1-1/2" drill point, black) to the wall.
11. Slide the 90
o
elbow (crimp end up) and the 2
ft. or 4 ft. pipe section (crimp end up) over the
4" dia. flex liner.
12. Slide the trim collar over the adjustable pipe
sections to cover the joint of the telescopic
section.
13. Install the spring spacers onto the pipe sections.
14. Secure the 4" dia. flex liner with adapter onto
the stove collar. Put a bead of Mill-Pac around
the appliance adapter and secure with 3 screws
(#8 x 1/2, stainless steel).
15. Attach the pipe section onto the starter collar
by sealing with Mill-Pac and securing with 3 of
the #8 x 1/2" (black) screws. Pipe seams should
be facing the wall.
16. Attach the 90
o
elbow onto the pipe section by
sealing with Mill-Pac and securing with 3 of the
#8 x 1/2" screws (black).
17. Slide the adjustable pipe section onto the 90 o
elbow. The flex may have to be compressed back
in order for the adjustable pipe to properly mate
to the elbow. Seal with Mill-Pac and secure with
3 of the #8 x 1/2" screws (black). Pipe seams
facing down.
18. Install the trim collar over the starter collar and
secure with a #8 x 1/2" screw (black).
If the pipe needs to be touched up, use only Stove
Brite High Temperature Metallic Black Stove Paint.
NOTE: For best results and optimum perfor-
mance with each approved venting system, it is
highly recommended to apply “Mill-Pac” sealant
(supplied) to every inner pipe connection. Failure
to do so may result in drafting or performance
issues not covered under warranty.
5. Slide the partially connected pipe and vent
terminal assembly through the wall thimbles
(from the exterior into the interior) and secure
the cap to the exterior wall with 4 of the supplied
screws (#8 x 1-1/2" drill point,
stainless steel). Note: pilot
holes will need to be drilled
through the wall thimble on
all 4 corners.
Note: The four screws
provided for the
vent cap should be replaced with
appropriate fasteners for stucco,
brick, concrete, or other types of
sidings.
6. A bead of non-hardening mastic should be run
around both the termination and vinyl siding
standoff to prevent water from entering and
to make a tight seal between the cap and the
standoff.
7. Stretch the 4" dia. flex liner out fully and get a
trial fit of the liner onto the 4" dia. starter collar.
8. Cut the 4" dia. flex liner to the desired size.
Hint: leave an extra 12" to 16" of length, this will
make the final assembly easier to work with.
For vinyl siding standoff installation
refer to the Dura-Vent Termination
instructions.