Regency Fireplace Products Greenfire GF1500L Скачать руководство пользователя страница 42

Страница: 42 / 76

42 |

Greenfire® GF1500L-2 Gas Fireplace

installation

Conversion Kit from NG to propane/ULPG Using SIT 845 NOVA Gas Valve

Refer to instructions provided with conversion kit for most up to date instructions.

920-355

11/26/20

PRIOR TO CONVERSION, ENSURE UNIT HAS COOLED TO ROOM
TEMPERATURE, ALL POWER IS DISCONNECTED AND GAS SUPPLY
IS TURNED OFF.

1. Remove faceplate, glass door, front trim piece- see instructions in this

manual.

2. Remove logs.
3. Remove burner side panels by lifting out as shown in Diagram 1.
4. Remove inner panels.

Diagram 3 - Burner Screw Locations

CONVERSION KIT FROM NG TO PROPANE/ULPG

FOR GF1500L-2 PART #607-967 USING SIT 845 NOVA GAS VALVE

THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER

IF IN DOUBT DO NOT DO THIS CONVERSION !!

Each Kit contains one Propane / ULPG

Conversion Kit

Qty.

Part #

Description

904-431

Burner Orifice#49 ULPG

904-434

Burner Orifice #47 LP

918-590

Decal “Converted to LP”

919-728

Orange Propane Label

918-272

Conversion to ULPG decal

904-529

5/32” Allen Key

910-037

Injector Orifice LP #30

919-727

Red Universal LPG label

920-355

Instruction Sheet

911-328

Pressure Switch

911-240

Brown Connecting Wire

920-356

Propane/ULPG Wiring Diagram

Diagram 4 - Remove Pilot Cap

Pilot Cap

Pilot Orifice

Pull off the pilot cap to expose the pilot orifice (see below).

Unscrew the pilot orifice with the Allen key and replace with

the propane/ULPG pilot orifice in the kit and replace pilot cap
(see right).

10.

Remove burner orifice with a 12mm spanner and discard. Use
another spanner to hold on to the elbow below the orifice.

Diagram 1 - Burner Side Panels

IT WOULD BE BENEFICIAL TO CONVERT THE APPLIANCE PRIOR TO
THE UNIT BEING INSTALLED OR WALL FACING MATERIAL FITTED
WHICH ALLOWS ACCESS TO THE BOTTOM PANEL.

Diagram 2 - Rear Log Tray Screw Locations

5. Remove rear log tray by removing 3 screws as shown in Diagram 2 below.

6. Unscrew the 2 front NG log pins. Relocate those pins to the rear holes

and reinstall.

Propane/ULPG
Natural Gas

Remove burner by removing 3 screws in locations shown
below.

GF1500L-2

Содержание Greenfire GF1500L













































































Результаты поиска

Содержание Greenfire GF1500L

Отзывы:

Похожие инструкции для Greenfire GF1500L

Бренды по названию

Популярные бренды

Regency Fireplace Products Greenfire GF1500L, Инструкция для владельца и по установке

Результаты поиска

Содержание Greenfire GF1500L

Отзывы:

Похожие инструкции для Greenfire GF1500L

Бренды по названию

Популярные бренды