Regency Fireplace Products Greenfire GF1500L Скачать руководство пользователя страница 19

Страница: 19 / 76

Greenfire® GF1500L-2 Gas Fireplace

| 19

installation

Optional Framing Kit

920-194

01/28/20

OPTIONAL FRAMING KIT

Construct the timber framing, ensure inside dimensions are 1095 mm H

x 1394 mm W as shown below.

2. Bend both side nailing strips from the side of the appliance until

positioned as shown below. Determine the overall combined thickness
of the non-combustible board + finished material being used. The
nailing strips can be adjusted up to 38mm. Remove top nailing strip and
recycle.

3. Adjust the nailing strips by loosening 2 screws on each nailing strip -

adjust and retighten screws.

NOTE:

depending on the finishing material used.

4. Attach both vertical studs (607-065) to the vertical timber studs and

secure using 6 screws, as shown.

NOTE

: Ensure the flat side of the steel stud is facing the timber framing.

(607-065)

Flat side out

5. Secure horizontal steel header stud

(606-067)

with 2 screws per side as

per diagram.

6. Slide the unit into position. Hook up gas, flueing, electrical and

conversion kit (if purchased) prior to installing the remaining steel studs.

7. Secure the upper horizontal steel stud

(606-067)

as shown with 2

screws per side.

8. Secure the top large horizontal stud

(607-027)

with 2 screws per side

as shown. Bring finishing material to the edge of the top framing lip on
large stud

(607-027).

9. Install the large lower stud

(607-066)

with 2 screws on each side.

Header stud

(606-067)

606-067

607-065

607-027

607-066

607-065

Nailing Strips

Remove Top

Nailing Strip

Large stud

(607-027)

Large stud

(607-066)

Horizontal stud

(606-067)

tooltip

Framing Lip

Finishing with

non combustible

material

Use Top Holes

Finishing with

combustible material

Use lower holes

GF1500L-1

Содержание Greenfire GF1500L













































































Результаты поиска

Содержание Greenfire GF1500L

Отзывы:

Похожие инструкции для Greenfire GF1500L

Бренды по названию

Популярные бренды

Regency Fireplace Products Greenfire GF1500L, Инструкция для владельца и по установке

Результаты поиска

Содержание Greenfire GF1500L

Отзывы:

Похожие инструкции для Greenfire GF1500L

Бренды по названию

Популярные бренды