Regency Fireplace Products Greenfire GF1500L Скачать руководство пользователя страница 14

Страница: 14 / 76

14 |

Greenfire® GF1500L-2 Gas Fireplace

installation

Installation of Access Panel

Remove top nailing strips & standoffs at side and under-
neath

1. Remove the top nailing strip/standoff by removing 4 screws in locations shown

in diagram to the right, then lift off and recycle.

Non Combustible Flush Finishing - Unit Assembly/Finishing/Mantel Clea Mantel Leg Clearances

2. Break off the 8 standoffs with a pair of pliers.

Remove 8 standoffs

Installation Access Panel

Tab locations on access panel

The  unit  is  equipped  with  a  removable  access  panel  for  pre-finish
installation  of  optional  components    -    this  panel  is  located  on  the
lower front face.

1. Remove 4 screws to remove access panel.

2. Easier access to gas connection with panel removed.

3. Install any optional components with access panel removed.

4. Reinstall access panel, line up 2 upper tabs and secure in place

with 4 screws.

Note:

Access panel is no longer usable/accessible once facing material
installed.

Содержание Greenfire GF1500L













































































Результаты поиска

Содержание Greenfire GF1500L

Отзывы:

Похожие инструкции для Greenfire GF1500L

Бренды по названию

Популярные бренды

Regency Fireplace Products Greenfire GF1500L, Инструкция для владельца и по установке

Результаты поиска

Содержание Greenfire GF1500L

Отзывы:

Похожие инструкции для Greenfire GF1500L

Бренды по названию

Популярные бренды