Regency Fireplace Products Greenfire GF1500L Скачать руководство пользователя страница 15

Страница: 15 / 76

Greenfire® GF1500L-2 Gas Fireplace

| 15

installation

Clearances For Non Combustible Flush Finishing with Mantel

Due to the extreme heat this fireplace emits, the mantel
clearances are critical.

Combustible mantel clearances from top of front facing are shown
in the diagram on the right.

Non Combustible Mantel Leg Clearances

Mantel leg & Non-combustible finishing clearances as per diagram: (Flushed Finish)

Allowablemantel

leg projection

181mm

254mm

330mm

38mm

MANTELLEG

102mm

178mm

Allowablemantel

leg projection

181mm

254mm

330mm

38mm

MANTELLEG

102mm

178mm

Allowablemantel

leg projection

181mm

254mm

330mm

38mm

MANTELLEG

102mm

178mm

83mm

Non-combustible

83mm

Non-combustible

Combustible Material

(152 mm)

(305mm)

(0 mm)

To Uni

Base

(617 mm)

(335 mm)

Top of

Fireplace

Opening

(589mm)

(305 mm)

(457 mm)

(254mm)

Non-Combustible facing (min.12 mm)

Non-Combustible steel stud

846 mm to underside

of steel stud

(100mm)

(310 mm)

(200mm)

(385 mm)

TES

• For a flushed finish using non-combustible finishing, seven

13mm stand-off tabs around the fireplace opening must
be broken off. The top nailing flange cannot be used and a
non-combustible steel stud must be installed to support the
non-combustible facing.

• Ensure the paint that is used on the mantel and the facing

is high quality or the paint may discolour.

Содержание Greenfire GF1500L













































































Результаты поиска

Содержание Greenfire GF1500L

Отзывы:

Похожие инструкции для Greenfire GF1500L

Бренды по названию

Популярные бренды

Regency Fireplace Products Greenfire GF1500L, Инструкция для владельца и по установке

Результаты поиска

Содержание Greenfire GF1500L

Отзывы:

Похожие инструкции для Greenfire GF1500L

Бренды по названию

Популярные бренды