RedWing RC Edge 540 v3 Скачать руководство пользователя

Страница: 19 / 20

STRONG DESIGNS RW EDGE 540V3 30CC

OPTIONAL:

Air Dam

•Included in the kit is an air dam to divert the
air from the cowl thru a cutout in the forward
fuselage ahead of the landing gear.

•Remove the covering from the outlet.

•Predrill the holes for the plate and thread
them using the include mounting screws.
Harden the threads with thin CA before final
installation.

SFG’s and Wing Tips

•Install the side force generators (SFG’s) and
wing tips to the wing. The SFGs are installed
using the screws provided with a drop of thread
locking compound on each screw. There are
blind nuts preinstalled in each wing tip.

•The wing tips are easily secured with magnets
and tabs which lock them in place.

NOTE:

If using the tips, make certain the SFG is

installed facing correctly to maintain proper
polarity of the magnets to the tips.

Содержание Edge 540 v3





















Результаты поиска

Содержание Edge 540 v3

Отзывы:

Похожие инструкции для Edge 540 v3

Бренды по названию

Популярные бренды

RedWing RC Edge 540 v3, Руководство пользователя

Результаты поиска

Содержание Edge 540 v3

Отзывы:

Похожие инструкции для Edge 540 v3

Бренды по названию

Популярные бренды