background image

STRONG DESIGNS RW EDGE 540V3 30CC 

 

15 

 

 
NOTE: 

gusseted 
mount is 
included 
and can 

be mounted anywhere in 
the forward fuselage 
using 15 min epoxy. 
Ensure you do not 
interfere with the position of the other 

components that will be 
installed later such as the fuel 

tank and 

ignition.  

 

 

 

 

 
 
 
--For a Twin, the low carb position requires a 
lower mounting of the 
throttle servo as shown 
in the floor of the motor 
box. 
 
 
 
•Determine the mounting position and prepare 
the servo. Install the grommets,  inserts, and 
secure the extension to the lead at this time. 

 

 

 
 
 
 
 

From the Pro:

 Use heat shrink 

tube to secure the servo lead to 
the extension. 

 
 
•Drop the servo into place and drill for the 
servo screws with a 1/16” drill bit.  Then, 
remove the servo and thread a servo screw in 
and out of each hole. Then apply 2 drops of thin 
CA to each and allow the CA to soak in and fully 
cure.   
 
•Before installing the throttle linkage, 
determine the position of the ignition module, 
fuel line routing thru the firewall, and choke 
linkage so that you may remove the engine and 
drill all holes needed at the same time.  
 
•Once all holes have been drilled, you may 
reinstall the engine for final assembly using 
thread lock compound.  
 
•Install the throttle servo and the linkage to the 
carburetor.   

 

 
 
From the Pro:

 The throttle arm on the carb and the 

servo horn should be of the same length to allow full 
servo resolution and better/finer throttle control.

 

              

Содержание Edge 540 v3





















Отзывы: