Redvision VEGA 2010-PW Скачать руководство пользователя

Страница: 3 / 30

Vega 2010-PW Installation Guide

Version 1.5 June 2019

Contents

1.0 Introduction

1.1 Product Features/ WEEE Directive

1.3 Safety

1.4 Parts supplied/ Available

2.0 Specifications

3.0 Installation

3.1 Wall Bracket (Standard Fitting)

3.2 Removing the bracket to aid wall fixing

3.3 PED mount: fitting instructions

4.0 Fitting the camera into the housing

4.1 Removing the housing cover

4.2 Housing Interior and parts

4.21 Installing the camera & lens assembly

4.30 Connecting the camera & lens assembly

5.0 CHAT

Interface board connections

5.1 CHAT

board layout

5.20 Power and Data connections

5.21 PoE+ (802.3at) connection

5.22 12VDC/ 24VAC connection

5.30 RS-485 data connection

5.31 DIP Switch settings

5.32 RS-485 protocol settings

5.33 SW1 Baud Rate settings

5.40 SW2 Camera ID settings

5.41 Wiper control settings

5.50 JP6 Aux control connections

5.60 User pass-through connections

5.61 Refitting the Housing cover

6.0 VEGA

Range and Accessories

7.0 Warranty Information

Содержание VEGA 2010-PW






























Результаты поиска

Содержание VEGA 2010-PW

Отзывы:

Похожие инструкции для VEGA 2010-PW

Бренды по названию

Популярные бренды

Redvision VEGA 2010-PW, Руководство по установке

Результаты поиска

Содержание VEGA 2010-PW

Отзывы:

Похожие инструкции для VEGA 2010-PW

Бренды по названию

Популярные бренды