REDSTONE | BP 36666, 59712 LILLE Cedex 9 | France
19 І 36
–
Wear suitable personal protective equipment.
This includes:
Hearing protection to avoid the risk of becoming
hearing impaired,
Respiratory protection to avoid the risk of inhal-
ing harmful dust,
–
Wear gloves when handling saw blades and
rough materials.
–
Carry saw blades in a container whenever practi-
cal.
–
Wear goggles. Sparks generated during work or
splinters, chippings and dust coming from the
device can lead to loss of eyesight.
–
Connect a dust collecting device to the electric
tool when sawing wood. The emission of dust
is influenced, among other things, by the type
of material to be processed, the significance of
local separation (collection or source) and the
correct setting of the hood/guide plates/guides.
–
Do not use saw blades made of high-speed alloy
steel (HSS steel).
–
In times of non-use keep the push stick or the
push block with the electrical power tool in its
holder at all times.
2
Maintenance and repair
–
Pull out the mains plug for any adjustment or
repair tasks.
–
The generation of noise is influenced by various
factors, including the characteristics of saw
blades, condition of saw blade and electric
tool. Use saw blades which were designed for
reduced noise development, insofar as possible.
Maintain the electric tool and tool attachments
regularly and if necessary, initiate repairs in
order to reduce noise.
–
Report faults on the electric tool, protective
devices or the tool attachment to the person
responsible for safety as soon as they are dis-
covered.
3
Safe work
–
Use the push stick or handle with sliding wood,
to pass the workpiece securely out off the saw
blade.
–
Make sure that the riving knife is always used,
and set up is correctly.
–
Use the upper blade guard and set it to the cor-
rect position.
–
Only use saw blades for which the maximum
permissible speed is not lower than the maxi-
mum spindle speed of table saws and which are
suitable for the material to be cut.
–
Do not cut rebates or grooves without fitting a
suitable guard, e.g. a tunnel-type guard, over the
saw table.
–
Circular saws must not be used for slotting jobs
(cutting grooves which end in the workpiece).
–
When transporting the electric tool, only use
the transport devices. Never use the protective
devices for handling or transport.
–
Make sure that the upper part of the saw blade
is covered during transport, e.g. by the protective
device.
–
Be sure to only use spacers and spindle rings
specified by the manufacturer as suitable for the
intended purpose.
–
The floor around the machine must be level,
clean and free of loose particles, such as chips
and cutting residues.
–
Always stand to the side of the saw blade when
working with the saw.
–
Do not remove any cutting residues or other
feed force during cutting, turn the machine off
and disconnect it from power supply. Remove
the work piece and ensure that the saw blade
runs free. Turn the machine on and start new
cutting operation with reduced feed force.
15
Do not leave a tool key inserted
–
Before switching on, make sure that keys and
adjusting tools are removed.
16
Avoid inadvertent starting
–
Make sure that the switch is switched off when
plugging the plug into an outlet.
17
Use extension cables for outdoors
–
Only use approved and appropriately identified
extension cables for use outdoors.
–
Only use cable reels in the unrolled state.
18
Remain attentive
–
Pay attention to what you are doing. Remain
sensible when working. Do not use the electric
tool when you are distracted.
19
Check the electric tool for potential damage
–
Protective devices and other parts must be care-
fully inspected to ensure that they are fault-free
and function as intended prior to continued use
of the electric tool.
–
Check whether the moving parts function fault-
lessly and do not jam or whether parts are dam-
aged. All parts must be correctly mounted and all
conditions must be fulfilled to ensure fault-free
operation of the electric tool.
–
The moving protective hood may not be fixed in
the open position.
–
Damaged protective devices and parts must be
properly repaired or replaced by a recognised
workshop, insofar as nothing different is speci-
fied in the operating manual.
–
Damaged switches must be replaced at a cus-
tomer service workshop.
–
Do not use any faulty or damaged connection
cables.
–
Do not use any electric tool on which the switch
cannot be switched on and off.
20
ATTENTION!
–
Exercise elevated caution for double mitre cuts.
21
ATTENTION!
–
The use of other insertion tools and other acces-
sories can entail a risk of injury.
22
Have your electric tool repaired by a qualified
electrician
–
This electric tool conforms to the applicable safety
regulations. Repairs may only be performed by an
electrician using original spare parts. Otherwise
accidents can occur.
23
Do not use the cable for purposes for which it
is not intended
–
Do not use the cable to pull the plug out of the
outlet. Protect the cable from heat, oil and sharp
edges.
ADDITIONAL SAFETY INSTRUCTIONS
1
Safety precautions
–
Warning!
Do not use damaged, cracked or
deformed saw blades.
–
Replace a worn table insert.
–
Only use saw blades recommended by the
manufacturer which conform to EN 847-1.
m
Warning!
Keep attention When changing the
saw blade.The cutting width is not smaller and
the main blade thickness of the saw blade is not
greater than the thickness of the gap wedge!
–
Make sure that a suitable saw blade for the ma-
terial to be cut is selected.
