Redline Communications RDL-2000 Скачать руководство пользователя страница 7

Страница: 7 / 52

RDL-2000

Installation Guidelines

70-00144-01-01

Page

of 52

March 9, 2011

Important Safety & Service

Notices

1.1 Safety Warnings

PoE power adapter for RDL-2000:

Warning to Service Personnel: 48 VDC

Customer equipment including personal computers, routers, etc., must be

connected only to the INPUT (DATA) port on the PoE unit.
Only the outdoors Ethernet interface cable connecting to the unit can be safely

connected to the OUTPUT (DATA & POWER OUT) connector. Connecting

customer premises Ethernet equipment directly to the OUTPUT (DATA & POWER

OUT) connector on the Power-over-Ethernet power adapter may damage customer

equipment.

Installation of the system must be contracted to a professional installer.

The installer is responsible for ensuring that the system is used exclusively for fixed,

point-to point operations.

Read this user manual and follow all operating and safety instructions.

Keep all product information for future reference.

The power requirements are indicated on the product-marking label. Do not exceed

the described limits.

Disconnect the power before cleaning. Use only a damp cloth for cleaning. Do not

use liquid or aerosol cleaners.

Disconnect power when unit is stored for long periods.

The unit must not be located near power lines or other electrical power circuits.

10.

The system must be properly grounded to protect against power surges and

accumulated static electricity. It is the user’s responsibility to install this device in

accordance with the local electrical codes: correct installation procedures for

grounding the unit, mast, lead-in wire and discharge unit, location of discharge unit,

size of grounding conductors and connection requirements for grounding electrodes.

1.2 Warning Symbols

The following symbols may be encountered during installation or troubleshooting. These

warning symbols mean danger. Bodily injury may result if you are not aware of the safety

hazards involved in working with electrical equipment and radio transmitters. Familiarize

yourself with standard safety practices before continuing.

Electro-Magnetic Radiation

High Voltage

Chapter 1

4Gon www.4Gon.co.uk [email protected] Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299

Содержание RDL-2000





















































Результаты поиска

Содержание RDL-2000

Отзывы:

Похожие инструкции для RDL-2000

Бренды по названию

Популярные бренды

Redline Communications RDL-2000, Руководство по установке

Результаты поиска

Содержание RDL-2000

Отзывы:

Похожие инструкции для RDL-2000

Бренды по названию

Популярные бренды