Redline Communications RDL-2000 Скачать руководство пользователя страница 17

Страница: 17 / 52

RDL-2000

Installation Guidelines

70-00144-01-01

Page

of 52

March 9, 2011

4.1.2 Customer Supplied Materials

Installation of the RDL-2000 equipment requires additional equipment and materials

supplied by the customer. The following list is provided as a guideline only, and

additional materials may be required based on local conditions at each installation site.

This list is not comprehensive and is provided as a guide only.

Table 7: Installation - Customer-Supplied Items

# Item

Description

1 Equipment Rack Mounting space allocated for the PoE power adapter. Must

accommodate 2 m (6') AC power cable and routing of Ethernet cable

from PoE to local Ethernet network access point.

120/240 VAC

Power

Reliable 120/240 VAC. Total power requirements must be

evaluated based on individual site configurations.

Cat-5 Ethernet

Cables

Connect from PoE power adapter to core network.

Cable

Installation

Materials

Materials for securing cables to mast, protecting cables from

abrasion, etc. including suggested weatherproofing materials:

Scotch 2200 series of vinyl mastic rolls

Scotch 130C linerless rubber splicing tape

3M Scotch super 88 electrical tape

Rubber mastic putty or duct sealing putty

Radio/Antenna

Mast

Mast or tower location as required by site survey. Equipment must be

rated for weight and wind loading of all installed radios and antennas.

6 Ground Block

Termination for grounding and shield of all conductive cables entering

the building.

Grounding

Wire

Master grounding system for all indoor and outdoor equipment,

with #2 AWG through #6 AWG as required and eye-terminals for

connection to RDL-2000 chassis and mounting bracket.

8 Tools

i) Equipment to terminate CAT-5 Ethernet cable with RJ-45 connector

(e.g., AMP 2-231652 or equivalent).

ii) Precision set of screwdrivers, cutter pliers, and other common

installation tools.

iii) Portable computer (Windows™) for RDL

-2000 configuration,

antenna alignment, and troubleshooting as required.

4Gon www.4Gon.co.uk [email protected] Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299

Содержание RDL-2000





















































Результаты поиска

Содержание RDL-2000

Отзывы:

Похожие инструкции для RDL-2000

Бренды по названию

Популярные бренды

Redline Communications RDL-2000, Руководство по установке

Результаты поиска

Содержание RDL-2000

Отзывы:

Похожие инструкции для RDL-2000

Бренды по названию

Популярные бренды