Redline Communications RDL-2000 Скачать руководство пользователя страница 5

Страница: 5 / 52

RDL-2000

Installation Guidelines

70-00144-01-01

Page

of 52

March 9, 2011

Weatherproof LP Connections .....................................................................37

4.5.4

Install Indoor PoE Power Adapter ...................................................................38

4.5.5

Step 5: Configure the RDL-2000 .....................................................................39

4.5.6

List of Required Parameters............................................................................39

4.5.7

Installing the Link Manager Application ...........................................................40

4.5.8

Start a Session with an RDL-2000 ..................................................................40

4.5.9

Configure PTP Slave.......................................................................................41

4.5.10

Configure PTP Master.....................................................................................44

4.6

Step 6: Antenna Alignment .............................................................................47

4.6.1

Basic Antenna Alignment ................................................................................47

Antenna Polarization ....................................................................................47

Azimuth Alignment .......................................................................................47

Elevation Alignment .....................................................................................47

4.6.2

Fine Antenna Alignment Using RSSI...............................................................47

Reference Information..........................................................49

5.1

Protecting Cables from High Temperature & Abrasion.................................49

5.2

Bench Test Setup.............................................................................................50

5.2.1

Customer Supplied Equipment:.......................................................................50

5.2.2

Assemble Test Setup......................................................................................50

5.2.3

Connectivity Test ............................................................................................50

5.2.4

Throughput Test..............................................................................................51

LIST OF TABLES

Table 1: FCC & IC RF Recommended Safe Separation Distances .................................. 9

Table 2: Site Survey - Site Path Profile Data ................................................................. 13

Table 3: Site Survey - Network Plan Data ......................................................................14

Table 4: Site Survey - RF Plan Data ..............................................................................14

Table 5: Site Survey - Additional Parameters ................................................................14

Table 6: Installation - Redline-Supplied Items ................................................................16

Table 7: Installation - Customer-Supplied Items ............................................................17

Table 8: Procedures - Lightweight Mounting Bracket - Parts List ...................................20

Table 9: Installation - Outdoor Ethernet Cable Termination ...........................................28

Table 10: Outdoor Line Protection Wiring Diagram ........................................................36

Table 11: Lightning Protection - Mounting Kit Parts List.................................................36

Table 12: Installation - Step by Step Configuration of RDL-2000 ...................................39

LIST OF FIGURES

Figure 1: Overview - RDL-2000 System Features .........................................................11

Figure 2: Site Survey - Fresnel Zone Radius ................................................................. 12

Figure 3: Site Survey - Non-Line of Sight Deployment ...................................................13

Figure 4: Installation - Redline Supplied Components ...................................................15

Figure 5: Installation - RDL-2000 System Components .................................................18

Figure 6: Procedures - Lightweight Mounting Kit - Installed View...................................19

Figure 7: Procedures - Lightweight Mounting Kit - Bracket Arm .....................................20

Figure 8: Procedures - Lightweight Mounting Kit - Assembly Drawing ...........................21

4Gon www.4Gon.co.uk [email protected] Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299

Содержание RDL-2000





















































Результаты поиска

Содержание RDL-2000

Отзывы:

Похожие инструкции для RDL-2000

Бренды по названию

Популярные бренды

Redline Communications RDL-2000, Руководство по установке

Результаты поиска

Содержание RDL-2000

Отзывы:

Похожие инструкции для RDL-2000

Бренды по названию

Популярные бренды