background image

APOLLO FYM - SPREADER CONTROLLER

2

Electromagnetic Compatibility (EMC)

This  product  complies  with  Council  Directive  2004/108/EEC
when  installed  and  used  in  accordance  with  the  relevant
instructions.

IMPORTANT, READ THIS BEFORE USING THE PS8000i

The

PS8000i

installation  is  a  part  of  the  Precision  Farming

System ("the System"). It is very important that you follow the
described  calibration  procedures  before  operating  the

PS8000i

instrument.  Calibration and operation of the

PS8000i

must  be  in  accordance  with  these instructions.  Use  of  the
System is subject to the following disclaimer;

1. So far as is legally permissible RDS Technology ("RDS"), or its

distributors,  shall  not  be  liable,  whatever  the  cause,  for  any

increased  costs,  loss  of  profits,  business,  contracts,  income,
or  anticipate  savings  or  for  any  special,  indirect  or
inconsequential  damage  whatsover  (death  or  personal  injury
excluded).

2. The  capabilities  and  functions  of  the  Precision  Farming

System  ("the  System")  are  limited  as  set  out  in  the
specification  of  the  System,  details  of  which are  contained in
the  Help  files  and product  literature  and  which  must  be  read
before using the System.

3. Without  prejudice  to  the  generality  of  the  above  it  is  hereby

acknowledged  that  the  System  is  not  designed  nor  intended

to a) originate variable treatment plans or b) achieve or avoid
any  application  rate  outside application  parameters,  which  in
both cases shall be the responsibility of the operator.

4. The standard terms and conditions of RDS (except clause 7),

a  copy  of  which  is  available  on  request,  apply  to  the  supply
and operation of this System.

Service and Technical Support

PLEASE CONTACT YOUR NEAREST RDS DISTRIBUTOR If
unknown then contact RDS Technology Ltd for further

information,
Tel :

+44 (0) 1453 733300

Fax :

+44 (0) 1453 733311

e-mail :

[email protected]

web :

www.rdstec.com

Our policy is one of continuous improvement and the
information in this document is subject to change without
notice. Check that the software reference matches that
displayed by the instrument.

© Copyright RDS Technology Ltd 2013

\UK746110.DOC

Содержание Apollo FYM


















Отзывы: