Rayco C120R Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 100

background image

C120R Operator Service Maintenance Manual

24

Operation

Pre-Start Procedure

Walk-Around Inspection

For maximum service life of the machine, make a thorough
walk-around inspection. Inspect the machine for the following:

•  Loose bolts
•  Trash buildup
•  Oil leaks
•  Broken parts
•  Worn parts

Inspect the overall condition of the machine and its hydraulic
components.
Check the engine oil level, the hydraulic oil level, and the
fuel level.
Refer to the Maintenance Interval Schedule for all service
recommendations.

Mounting and Dismounting

• Get on or off the machine only at locations that are

equipped with steps (1) and/or hand holds.

• Before you get on the machine, clean and inspect the

steps and the hand holds. Make all necessary repairs.

• Face the machine whenever you get on or off the machine.
• Maintain a three-point contact with the steps and

hand holds.

Note: Three-point contact can be two feet and one hand, or
one foot and two hands.

•  Do not get on or off a moving machine.
•  Never jump off the machine.
•  Do not try to get on or off the machine if you are carrying

tools or supplies. Use a hand line to pull equipment

onto the platform.

• Do not use any controls as hand holds when you enter

or exit the operator’s compartment.

Seat and Seat Belt Inspection

Adjust the seat at the beginning of each work period. Also
adjust the seat when you are changing operators.
Inspect the seat belt mounting hardware. Replace any
hardware that is damaged or worn. Keep the mounting
bolts tight.
Fasten the seat belt before you start the engine.

Emergency Exit

Familiarize yourself with the alternate exits. In the event that
the primary exit is blocked, the top window hatch may be
removed as well as the side window.

The top exit window is accessible from inside the cab only.
The escape window is fastened with 3 levers (3) located
directly above the operator seat. To remove window turn
levers 1/4 turn and push out.

The side window can be removed
from the inside or outside the cab.
On the inside turn the levers 1/4
turn and push out the same way as the top exit window. To
remove the window from the outside, remove the knob (2a)
by turning it counter clockwise until removed.

1

3

2

2a

«
...
22
23
24
25
26
...
»

Содержание C120R





































































































Отзывы:

Нет отзывов

Похожие инструкции для C120R

Бренд: Bacharach Страницы: 31

Бренд: Bacharach Страницы: 2

Бренд: Cannon Страницы: 40

Бренд: IDEAL Networks Страницы: 60

Бренд: Madsen Страницы: 206

Бренд: Gardenline Страницы: 24

Бренд: Torrent Страницы: 23

TEMSTM POCKET 7.3

Бренд: ASCOM Страницы: 8

Бренд: OHAUS Страницы: 2

Бренд: Tissue-Tek Страницы: 42

Unidrill-W Series

Бренд: Moore Страницы: 46

Бренд: P.Lindberg Страницы: 26

Бренд: Tracmaster Страницы: 32

Бренд: wittek Страницы: 11

Бренд: WalimeXPro Страницы: 23

SEEDMATIC PROFESSIONAL 8124A

Бренд: Aitchison Страницы: 50

Бренд: Troy-Bilt Страницы: 40

Бренд: Anderson Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды