Ravenheat CSI 85 Скачать руководство пользователя страница 21

Страница: 21 / 55

KEY

63 -Air intake duct extension

56 - Sample point

64 - Flue Exhaust duct extension

57 - Elbow Header

65 - Pipe centering spring

59 - Rubber seal 0 60

128 - In Line Bend

5.7.2

Positioning the elbow towards the required

- Reassemble the two tubes.

direction (Fig. 30).

Insert centering spring 65.

5.7.3

5.7.5

Locate the 0 60 into the elbow (Fig. 30).

- If the standard duct furnished with the

boiler is too long (position of the boiler

from the wall to go through as illustrated

in the drawing and wall thicknesses less

than what was specified above) it can be

shortened as follows: Fig.28-29-31-32.

- Remove the centering spring 65, pull

the flue terminal disengage inner flue
duct.

Measure the thickness W of the wall.

- Cut the outer air duct (100 mm. dia.) at

right angles and to a length equal to

W+Y - 47 mm. (Fig. 32).

- Cut the inner flue duct (60 mm. dia.) at

right angles and to a length equal to

W+Y + 65 mm.

- Outer air duct and inner flue duct must

be de-burred.

5.7.12

VERTICAL FLUE INSTRUCTIONS ONLY

6.7.6

Insert the flue assembly into the wall,

making sure it will not interfere when fixing
the boiler on the wall.

5.7.7

Lift the boiler on the wall. Locate onto the

top coach bolts. Fit the lower coach bolts

and tighten all four securing bolts.

5.7.8

Working above the boiler pull the flue duct

towards the elbow in order to engage tube

into its header (Fig. 35).
Position flue into straight header and push
so as to locate inner and outer flue correctly.
Ensuring good seal is made with o.rings.

5.7.10 IMPORTANT:

Terminal rubber must be

fitted (Fig. 37).

5.7.11

Extension kits are available on order for

flue extension of up to 2.5 metres total

length (Fig. 31). For further details see sect

5.5.10.

Fig. 40

Fig. M

Содержание CSI 85
























































Результаты поиска

Содержание CSI 85

Отзывы:

Бренды по названию

Популярные бренды

Ravenheat CSI 85, Инструкции по установке и обслуживанию

Результаты поиска

Содержание CSI 85

Отзывы:

Бренды по названию

Популярные бренды