Ravenheat CSI 85 Скачать руководство пользователя страница 14

Страница: 14 / 55

SALAMANDER CURROSION GUARD

Fig. 10

Salamander (Eng) Ltd
Tel: (0121) 3780952/4508

4.8.10

Hard water areas

If the area of-installation is recognized as

hard water, it is recommended that a suit-
able water treatment device is installed in
the mains.

The water hardness can be determined by

using the standard test paper or by referring

to local water authority.

4.9

4.9.1

4.10

4.10.1

DOMESTIC WATER

The domestic hot water must be in accor-
dance with the relevant recommendations of

BS 5546. Copper tubing to BS 2871. 1 is
recommended for water carrying pipework
and MUST be used for pipework carrying
potable water.

ELECTRICAL SUPPLY

Warning: this appliance must be earthed

External wiring to the appliance must be
carried out by a competent person and be in
accordance with the current I.E.E. Regula-

tions and local regulations which apply.
The Ravenheat boiler is supplied for con-

nection to a 230 V - 50 Hz single phase sup-
ply. The

supply must be fused at 3 A.

NOTE: The method of connection to the
electricity supply MUST facilitate complete
electrical isolation of the appliance, by the
use of a fused, double pole isolator, having a

contact separation of at least 3 mm in all

poles. The point of connection to the elec-

tricity supply must be readily accessible and
adjacent to the appliance except, where the

appliance is installed in a bathroom, this
MUST be sited outside the bathroom.

SECTION

5 INSTALLATION

5.1

WARNING

5.1 .1

It is MOST IMPORTANT that this appliance
is installed in a VERTICAL POSITION, with

the flue air duct passing through the wall.

Make sure flue slopes 2.5

down towards

the boiler that is 45 mm/m fall per metre

of flue

length.

Fig. 11

Содержание CSI 85
























































Результаты поиска

Содержание CSI 85

Отзывы:

Бренды по названию

Популярные бренды

Ravenheat CSI 85, Инструкции по установке и обслуживанию

Результаты поиска

Содержание CSI 85

Отзывы:

Бренды по названию

Популярные бренды