Ravelli HR EVO 200 SMART, Инструкция по установке, использованию и техническому обслуживанию

Страница: 74 / 212

HR EVO 200-250 SMART
use and maintenance manual
Pag.74
Rev.0 03/07/2019
ENG
Lighting
Check before lighting
Before lighting the boiler:
- make sure to have read and understood the information given in the manual;
- follow the oral instructions on operation of the unit provided by the installer prior to use.
- the hopper must be filled with pellets;
- the combustion chamber must be clean;
- the brazier must be completely free, cleaned of any combustion residuals and correctly fitted in the brazier holder;
- check hermetic closing of the ash box and fire door;
- check the connection of the power cable and switching to ON/1 of the switch located on the back of the boiler.
- check opening of the delivery and return shutoff valves as well as the water circuit pressure.
Any lighting done after long idle periods requires the removal of any residual pellets that have remained inside
the hopper, in being damp fuel no longer suitable for combustion, and complete cleaning of the combustion
chamber.
Startup stage
To light the boiler, press the button ‘P4’ for 3 seconds: the message ‘START’ will appear on the display.
This stage is automatic and managed entirely by the electronic controller without the possibility of changing the parameters.
Alternatively the boiler can be lit by pressing the buttons P4 and P5 together for 3 seconds. The message AWAITING REQUEST
appears on the display. With this mode the boiler switches to standby status and carries out the lighting-start stage only if a request
for heat is recognised, e.g. to heat the water or for DHW (if available).
The Figure opposite describes the meaning of the status
indicators in the left part of the display.
Activation of one of the segments on the display signals
activation of the corresponding device according to the list
opposite Dimensioni: 99 x 55,5mm.
Formato file: pdf vettoriale
coralDRAW X5
File:
stufa orizzontale Touch slim.cdr
Personalizzazione per: Micronova
MICRONOVA S.R.L.
Disegnatore: Michele Rossetti
18.04.2014 V:2.0
Grigio tortora
non conduttivo
Nero 10%
non conduttivo
Trasparente
Biadesivo 3M 9088
vista anteriore vista posteriore
SET
Ribassamento 1mm.
PNO100503PX00
Dimensioni: 99 x 55,5mm.
Formato file:
pdf vettoriale
coralDRAW X5
File:
stufa orizzontale Touch slim.cdr
Personalizzazione per:
Micronova
MICRONOVA S.R.L.
Disegnatore: Michele Rossetti
18.04.2014 V:2.0
Grigio tortora
non conduttivo
Nero 10%
non conduttivo
Trasparente
Biadesivo 3M 9088
vista anteriore vista posteriore
SET
Ribassamento 1mm.
PNO100503PX00
Dimensioni:
99 x 55,5mm.
Formato file: pdf vettoriale
coralDRAW X5
File: stufa orizzontale Touch slim.cdr
Personalizzazione per: Micronova
MICRONOVA S.R.L.
Disegnatore:
Michele Rossetti
18.04.2014 V:2.0
Grigio tortora
non conduttivo
Nero 10%
non conduttivo
Trasparente
Biadesivo 3M 9088
vista anteriore vista posteriore
SET
Ribassamento 1mm.
PNO100503PX00
Crono
Heater
Auger
Fume extractor
DHW circuit activation
HEATING circuit activation
ALARM
Clock
Storage tank-Puffer H20
Button ‘P4’
Water temperature
Dialogue
box