Raisecom RC3000 Скачать руководство пользователя страница 66

Страница: 66 / 105

www.raisecom.com

User Manual

PCB version: REV A.3 CPLD version: REV 1.0

Signal: None Receive Phase:Positive Transmit Phase:Positive

Channel: Main Channel

Local Loopback: No Loopback Remote Loopback: No Loopback

BER Test: Enable

7235 Auto Adjust Phase: Enable

Adjust Receive Phase: Enable(Clock Down)

DTR State: 0(Ready) RTS State: 0(Ready)

DCD State: 1(Unready) CTS State: 1(Unready)

BER

test

result:

Normal

Note

: parameters of phase adjustment: positive and negative;

Channel: main channel & Single channel

Loopback Set: No Loopback & Loopback

BER Test: Disable & Enable

Auto to Adjust Phase for Transmit: Enable & Disable

To Adjust Receive Phase: Enable & Disable

Status of DTR, RTS, DCD, CTS: Ready & Unready

BER test result: Normal & Abnormal; if you disable BER test, there will not be this item.

Sub-card type 7 V24 data user card:

Type: 7 V24 User Board Timeslot Number: 8 Set Mode: Hardware

PCB version: REV B.0 CPLD version: REV 1.0

Signal: None

Secondary CPLD version: REV1.0

Port 1: Bandwidth: 128kbps

Receive Phase: Negative Transmit Phase:Positive

Port 2: Bandwidth: 64kbps

Receive Phase: Negative Transmit Phase:Positive

Port 3: Bandwidth: 128kbps

Receive Phase: Negative Transmit Phase:Positive

Port 4: Bandwidth: 64kbps

Receive Phase: Negative Transmit Phase:Positive

Sub-card type 8 Ethernet data user card:

Type: 8 Ether Net Board Timeslot Number: 0 Set Mode: Hardware

PCB version: REV A.0 CPLD version: REV 1.0

Signal:None

Channel:Main Channel

Band Width Buffer:>512Kbps

Содержание RC3000










































































































Результаты поиска

Содержание RC3000

Отзывы:

Похожие инструкции для RC3000

Бренды по названию

Популярные бренды

Raisecom RC3000, Руководство пользователя

Результаты поиска

Содержание RC3000

Отзывы:

Похожие инструкции для RC3000

Бренды по названию

Популярные бренды