background image

2

 

/ 26

User Manual

Rev. 1.0 - 22/08/14

TEX1002LCD

 

Units returned without a return authorisation may 

be rejected and sent back to the sender.

4  Be  sure  to  include  a  detailed  report  mentioning  all 

problems  you  have  found  and  copy  of  your  original 

invoice (to show when the warranty period began) with 

the shipment.

Please send spare and warranty replacement parts orders to 

the address provided below. Make sure to specify equipment 

model and serial number, as well as part description and 

quantity.

 

R.V.R. Elettronica S.p.A. 

Via del Fonditore, 2/2c 

40138 BOLOGNA ITALY 

Tel. +39 051 6010506

 

3.  First Aid

All personnel engaged in equipment installation, operation 

and maintenance must be familiar with first aid procedures 

and routines.

 

3.1  Electric shock treatment

 

3.1.1  If the victim is unconscious

Follow the first aid procedures outlined below.

• 

Lay the victim down on his/her back on a firm 

surface.

• 

the neck and tilt the head backwards to free 
the airway system (

Figure 1

).  

Figure 1

• 

If needed, open the victim’s mouth and check 

for breathing.

• 

If there is no breathing, start artificial respiration 

without delay (

Figure 2

) as follows: tilt the head 

backwards, pinch the nostrils, seal your mouth 

around the victim’s mouth and give four fast 

rescue breaths.

Figure 2

• 

Check  for  heartbeat  (

Figure  3

);  if  there  is 

no  heartbeat,  begin  chest  compressions 

immediately (

Figure 4

) placing your hands in 

the centre of the victim’s chest (

Figure 5

).

 

 

             Figure 3 

     Figure 4 

Figure 5  

• 

One rescuer: give 2 quick rescue breaths after 

each 15 compressions.

• 

Two rescuers: one rescue breath after each 5 

compressions. 

• 

Do not stop chest compressions while giving 

artificial breathing.

• 

Call for medical help as soon as possible.

 

3.1.2  If the victim is conscious

• 

Cover victim with a blanket.

• 

Try to reassure the victim.

• 

Loosen the victim’s clothing and have him/her 

lie down.

• 

Call for medical help as soon as possible.

 

3.2  Treatment of electric burns

 

3.2.1  Large burns and broken skin

• 

Cover  affected  area  with  a  clean  cloth  or 

linen.

• 

Do not break any blisters that have formed; 

remove any clothing or fabric that is stuck to 

the skin; apply adequate ointment.

• 

Administer adequate treatment for the type of 

accident.

• 

Get  the  victim  to  a  hospital  as  quickly  as 

possible.

• 

Elevate arms and legs if injured.

If medical help is not available within an hour, the victim is 

conscious and is not retching, administer a solution of table 

salt  and  baking  soda  (one  teaspoon  of  table  salt  to  half 

teaspoon of baking soda every 250 ml of water).

Have the victim slowly drink half a glass of solution for four 

times during a period of 15 minutes. 

Stop at the first sign of retching.

Do not administer alcoholic beverages.

 

3.2.2  Minor Burns

• 

Apply cold (not ice cold) strips of gauze or dress 

wound with clean cloth.

• 

Do not break any blisters that have formed; 

remove any clothing or fabric that is stuck to 

the skin; apply adequate ointment.

• 

If needed, have the victim change into clean, 

dry clothing.

• 

Administer adequate treatment for the type of 

accident.

• 

Get  the  victim  to  a  hospital  as  quickly  as 

possible.

• 

Elevate arms and legs if injured.

Содержание TEX1002LCD





































Отзывы: