background image

 

Section 4 

 

Publication 9-86

 

 

Issue 1 : 10/22 

Section 9 

 

Publication 9-86 

Issue 1 : 10/22 

 

Page 1 of 10 

HB Products HBLT-A1 Liquid Level Transmitters 

Contents 

1.

 

About this Publication.................................................................................................... 2

 

1.1.

 

Safety Warnings and Symbols ................................................................................................. 2

 

1.2.

 

Units of Measurement .............................................................................................................. 2

 

1.3.

 

Terminology ............................................................................................................................. 2

 

1.4.

 

Additional Copies ..................................................................................................................... 2

 

2.

 

Introduction ................................................................................................................... 3

 

3.

 

Technical Data .............................................................................................................. 3

 

4.

 

Operation ...................................................................................................................... 5

 

5.

 

Installation ..................................................................................................................... 5

 

5.1.

 

General .................................................................................................................................... 5

 

5.2.

 

Wiring ....................................................................................................................................... 6

 

6.

 

Commissioning .............................................................................................................. 6

 

6.1.

 

Selecting the Refrigerant ......................................................................................................... 7

 

6.2.

 

Signal Damping........................................................................................................................ 7

 

6.3.

 

Calibration ................................................................................................................................ 8

 

6.3.1.

 

Adjusting the Minimum and Maximum Calibration Points ................................................. 8

 

6.3.1.1.

 

Minimum Calibration .................................................................................................... 8

 

6.3.1.2.

 

Maximum Calibration ................................................................................................... 8

 

6.3.1.3.

 

Minimum Calibration When the Minimum Liquid Level is Different From 4 mA ........... 8

 

6.3.1.4.

 

Maximum Calibration When the Maximum Liquid Level is Different From 20 mA ....... 9

 

6.4.

 

Restore Factory Default Settings ............................................................................................. 9

 

6.5.

 

LED Indication.......................................................................................................................... 9

 

7.

 

Maintenance ................................................................................................................ 10

 

8.

 

Faults and Remedies .................................................................................................. 10

 

9.

 

Spare Parts ................................................................................................................. 10

 

10.

 

Safe Disposal, End-of-life (EOL) ................................................................................. 10

 

List of Figures 

Fig 1 Arrangement, Dimensions and Model Numbers ............................................................................ 4

 

Fig 2 Installation ..................................................................................................................................... 5

 

Fig 3 Installation into Standpipe or Vessel .............................................................................................. 6

 

Fig 4 Wiring ............................................................................................................................................ 6

 

List of Tables 

Table 1 Technical Data ........................................................................................................................... 3

 

Table 2 Refrigerant Settings ................................................................................................................... 7

 

Table 3 Faults and Remedies ............................................................................................................... 10

 

 

J & E Hall International

©

 2022

 

All rights reserved.  No part of this publication may be reproduced or transmitted in any form or by 

any means, electronic or mechanical, including photocopying, recording or by any information 

storage or retrieval system, without permission in writing from the copyright holder. 
The copyright in this publication shall be and remain the sole property of J & E Hall International. 

Содержание HBLT-A1











Отзывы: