BES X system configurations
BES X installation manual
28
P/N: 400288005; Rev: L, 09/21
3.3.4
SuperTouch Lane console
In this configuration, the following devices are installed on each pair of lanes:
•
the camera (Q-Vision or T/M-Vision);
•
the pinspotter interface;
•
other optional LCOM devices (Bumper interface, Q-FOUL, TMR, etc.);
•
one 4HD/5HD-HUB;
•
one 4HD/5HD-CPU;
•
the overhead monitors (i.e. two overhead monitors);
•
two SuperTouch consoles.
The camera, pinspotter interface and the other optional LCOM devices are connected to the 4HD/5HD-HUB
via the LCOM cable (Refer to section
The L1 port of the 4HD/5HD-CPU is connected to the L1 port of the 4HD/5HD-HUB via a network cable.
Each overhead monitor is connected to the corresponding port of the 4HD/5HD-CPU unit with a HDMI cable.
If the monitors do not support commands via the HDMI, a serial communication cable (P/N:
288401007
)
must be installed between the overhead monitors and the 4HD/5HD-CPU in order to be controlled directly
from a Conqueror X computer.
The SuperTouch console version 2 (or higher) on the odd lane is connected to:
•
L3 port of the 4HD/5HD-HUB through a network cable (grey cable);
The SuperTouch console version 2 (or higher) on the even lane is connected to:
•
L4 port of the 4HD/5HD-HUB through a network cable (yellow cable);
Or
The SuperTouch console (PN:
288150024
) on the odd lane is connected to:
•
L3 port of the 4HD-HUB through a network cable (grey cable);
•
P1 port of the 4HD-HUB through a network cable (red cable): connect the network cable on the 4HD-
HUB side to the 288401035 cable adapter then the 288401035 cable adapter to the P1 connector of
the 4HD-HUB unit.
The SuperTouch console (PN: 288150024) on the even lane is connected to:
•
L4 port of the 4HD-HUB through a network cable (yellow cable);
•
P1 port of the 4HD-HUB through a network cable (blue cable): connect the network cable on the
4HD-HUB side to the 288401035 cable adapter, then connect the 288401035 cable adapter to the P1
connector of the 4HD-HUB unit.
In the case that an existing BES X bowling center, already equipped with SuperTouch consoles (P/N
288150024
), purchases EDGE String pinspotters, the existing 4HD-HUB units
MUST
be replaced with the 5HD-
HUB P/N:
288250025-01
or P/N:
288250025-02
units and the “5HD
-HUB to first gen. SuperTouch
–
cable
adapter” (P/N:
288401054
Each console must be connected to ground. Please refer to the section
Suggested ground connection
of the
BES X
–
Pre-Installation Manual
for further information.
Содержание 400288005
