background image

Quark-elec Manual

https://www.quark-elec.com

28 of 28

2018

V3

14. Limited Warranty and Notices

Quark-elec warrants this product to be free from defects in materials and manufacture for one year from

the date of purchase. Quark-elec will, at its sole option, repair or replace any components that fail in

normal use. Such repairs or replacement will be made at no charge to the customer for parts and labour.

The customer is, however, responsible for any transportation costs incurred in returning the unit to Quark-

Elec. This warranty does not cover failures due to abuse, misuse, accident or unauthorized alteration or
repairs. A returns number must be given before any unit is sent back for repair.

The above does not affect the statutory rights of the consumer.

Disclaimer

It is the user’s responsibility to use this product prudently. Neither Quark-, nor their distributors or dealers

accept responsibility or liability either to the products user or their estate for any accident, loss, injury or

damage whatsoever arising out of the use or of liability to use this product.

Quark- products may be upgraded from time to time and future versions may therefore not correspond

exactly with this manual. The manufacturer of this product disclaims any liability for consequences arising

from omissions or inaccuracies in this manual and any other documentation provided with this product.

Document history

Issue

Date

Changes / Comments

V1.0

04-12-2016 Initial release

V1.01

13-07-2018 Correct command error: OFFnhhmmss, should be OFnhhmmss#

V2

24/10/2018 New 2018 format

V3

28/11/2018

Quark-elec (UK)

Unit 7, the Quadrant

Newark close

Royston, UK

SG8 5HL

Содержание QK-G031





























Отзывы: