Quantum Scalar 10K Скачать руководство пользователя страница 268 | Manualshive

Страница: 268 / 324

background image

5-16

Processing Media

6-00058-05

Rev

A

Cleaning Drives

Most tape drives require occasional cleaning. The cleaning
cartridge cleans accumulated debris from the tape drive and
the read/write head.

Listed below are three methods for cleaning cartridge drives:

•

Host application software (default)

•

Scalar 10K firmware (selected from the operator panel)

•

Manual operation (performed by the operator)

Typical Cleaning Operation

Typically during normal operation, the host system moves
the data cartridges to and from drives.

During a move from a drive to a storage location in the
library, the application checks drive status. If the drive reports
that it requires cleaning, the system puts the cartridge it is
moving into storage, but does not notify the host that the
move is complete.

The system selects the cleaning cartridge, and inserts it into
the drive. After the cleaning is complete, the cartridge is
ejected from the tape drive and moved back to storage. The
library reports to the host that the move is complete.

Non-typical Cleaning

Listed below are several instances when a typical cleaning
operation cannot be performed.

•

Drive cleaning takes several minutes to complete. If the
host system does not wait for the cleaning to complete, it
reports an error.

•

If the library is set to delayed cleaning, the library waits
until a specified time before it performs the cleaning
operation.

•

If the drive type does not support drive communication to
the library, the library cannot automatically clean the
drive. The drive must be cleaned using application
software.

There are common items which are used for either Scalar 10K
firmware or host controlled drive cleaning. The following
items refer to several operator panel menus. All menu
information is detailed in

Menus and Commands

on page 4-1.

Note

Cleaning cartridges
have white labels
and the first three
letters for the Volser
number are CLN.

Note

Be aware that most
cleaning cartridges
are abrasive and
burnish the heads
of the drive they are
cleaning.
Burnishing causes
wear on the tape
drive heads.
Cleaning too
frequently can
reduce the life of a
tape drive.

Note

To avoid this event,
adjust the system
wait time. If the
system wait time
cannot be adjusted
to allow cleaning to
complete, clean the
drive manually or
use the library
firmware.

«
...
266
267
268
269
270
...
»

Содержание Scalar 10K





































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Scalar 10K

SO READY SECURE

Бренд: DANE-ELEC Страницы: 2

EliteRAID ER104I+

Бренд: Sans Digital Страницы: 64

Бренд: Décor et Jardin Страницы: 24

Бренд: Jimmy at work Страницы: 25

Бренд: SanDisk Страницы: 7

Бренд: HOLZMANN MASCHINEN Страницы: 18

Бренд: IBM Страницы: 2

Little Big Disk Quadra

Бренд: LaCie Страницы: 32

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 4

VAIO PCGA-HD740

Бренд: Sony Страницы: 7

Бренд: Sony Страницы: 16

VAIO VGP-UHDP04

Бренд: Sony Страницы: 23

Vaio VGP-UHDM10

Бренд: Sony Страницы: 27

VAIO VGP-UHDM08

Бренд: Sony Страницы: 27

Бренд: Sony Страницы: 89

Бренд: Sony Страницы: 127

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды